Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

Recent Posts

Pages: 1 [2] 3 4 ... 10

Started by arcadesteve123 - Last post by arcadesteve123

However...paradise is short lived as it seems that my mapping is now off.  When putting everything back together I swapped usb ports on the computer and somehow messed up the tankstick player controls. P1 on the left is now on the right and P2 is on the left as shown...ugh.

Hopefully there is an easy workaround?

Started by b4nd1t0 - Last post by arcadeswede

@b4nd1t0 Are you able to compile GroovyArcade with hiscore and cv1k fix?

Started by arcadesteve123 - Last post by arcadesteve123

Diy stand and tankstick together again!

14   Everything Else / Re: OND's other projects on Yesterday at 01:57:17 am

Started by Ond - Last post by Ond

Testing the fit of the Artisan panels:

Both Artisan enclosures glued up except for baffles. Most circular cuts were done with my router using a flush trim bit and the 3D printed cutting templates. I'm using threaded inserts for most screw fittings with either M4 or M5 Button head machine screws:



Here I've sealed the lower chamber of the Artisan enclosures with silicone. Crossovers screwed into place. The lower chamber will be filled with sand. You can just see the hole I've cut in the bottom to allow sand filling;

I'm starting to line the insides of these with foam. Once that's done I can glue the baffles into place:


Here I've just positioned the baffle in place and I'm making sure the drivers clear the port. Its a tight fit, the magnets on the back of each driver just clear the end of the port:


Here are the completed crossovers for the Carrera bookshelf speakers. These little bookshelf speakers are more costly to build than the tall floor standing Artisans.


Here are the Carrera enclosures with rebates finished and ports glued in place:

Soon I'll start looking at the third design, the most complex (and expensive!) the Sasandu speakers. I'll cover the 3D design prep I did in Fusion for CNC cutting the panels, and a first look at the 3 way Sasandu crossovers, built once again on my own PCBs...

Started by saint - Last post by Ond

ATS

Started by DaOld Man - Last post by DaOld Man

Hopefully I figured this out.

I ran ledwiz_configurator as administrator.
Then, in Global Options, I unchecked "Enable Debug Log"
It now runs from win startup with no errors.
If I re-enable the debug log, I get the error.

So Id say there is a bug in the debug log routine.
Hopefully this will help someone else who might have the same problem.

17   Audio/Jukebox/MP3 Forum / Rowe Ami Capacitors required.on February 09, 2025, 06:44:09 pm

Started by Scorpio Classics - Last post by Scorpio Classics

Capacitors needed to repair rowe ami r2179a stereo amplifier.
Can anyone advise on where to buy these? Many thanks.

Started by Scorpio Classics - Last post by Scorpio Classics

Have recently purchased another 6 problematic Rowe Ami jukebox and wondered if anyone could advise on possible cause?
Records are selecting as normal but fail to play until the end and seem to get stuck at various points. Can anyone help and point me in the right direction to fix the problem. Also need an original mid range speake if any available? Many thanks.

19   Arcade1Up & Similar / Arcade1UP Street Fighter online PCBson February 09, 2025, 12:44:14 pm

Started by bsoder52 - Last post by bsoder52

I'm interested in picking up a full size street fighter cabinet and installing a 1up PCB with online cabability. Wondering if all the online Street Figher issues have the same PCB or if I should/need to get the PCB that matches the cabinet I get?  My intent would be to use the PCB in conjunctiion with the geekworm board to run it on a 30" 3/4 LCD aftermarket arcade monitor in the cab. I may need to get a big blue cabinet to fit that monitor not sure yet.  Thanks for any advice, thoughts, resources, help.

Started by argonlefou - Last post by argonlefou

Sorry but no  :-\

Dolphin was too much of a headeache.
Pages: 1 [2] 3 4 ... 10