The NEW Build Your Own Arcade Controls
Main => Monitor/Video Forum => Topic started by: Sarver Systems on June 07, 2014, 06:58:30 pm
-
BULK REPAIR KIT FOR TECHS (https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=89e9d75a7a) Cost +/-$272.00
^^^click me for full shopping list^^^
ALUMINUM ELECTROLYTIC
- 25 100uf @ 200V
- 25 330uf @ 50V
- 25 33uf @ 35V
- 25 4.7uf @ 250V
- 100 1uf @ 50V
- 50 1uf @ 250V
- 10 1uf @ 450V
- 100 2.2uf @ 50V
- 25 2.2uf @ 250V
- 25 3.3uf @ 50V
- 25 3.3uf @ 250V
- 100 4.7uf @ 50V
- 25 4.7 @ 250V
- 100 10uf @ 50V
- 30 10uf @ 160V
- 30 10uf @ 250V
- 25 22uf @ 50V
- 25 22uf @ 250V
- 100 47uf @ 50V
- 20 47uf @ 250V
- 100 100uf @ 50V
- 25 100uf @ 160V
- 50 220uf @ 35V
- 30 470uf @ 35V
- 25 1000uf @ 25V
- 25 1000uf @ 35V
- 25 2200uf @ 35V
BIPOLAR ALUMINUM ELECTROLYTIC
- 20 1uf @ 50V BP
- 20 4.7uf @ 50V BP
- 20 10uf @ 50V BP
TANTALUM
FUSES AND PARTS
- 10 1.2A fuse
- 10 3A fuse
- 20 small fuse clips
- 20 large fuse clips
RESISTORS
- 10 1 ohm 1/2W
- 10 4.7k ohm 1/2W TBA
TRANSISTORS (optional)
- 5 2SD870 transistor (Bob Roberts)
- 5 2SD1398 transistor (Bob Roberts)
[/list]
-
PRICE WATCHER
$237.92 updated 6/10/14 (no back orders)
$242.82 updated 6/13/14 (no back orders)
$252.93 updated 7/1/14 (no back orders)
$264.07 updated 7/15/14 (no back orders)
$264.07 updated 7/18/14 (2 parts backordered)
$264.07 updated 7/23/14 (no back orders)
$264.07 updated 7/28/14 (2 parts on backorder)
$264.07 updated 8/3/14 (2 parts on backorder)
$264.07 updated 8/7/14 (2 parts on backorder)
$268.59 updated 8/10/14 (added fuse clips, added resistors, 1 part swapped due to backorders, 1 part backordered, see note above.)
$268.59 updated 8/15/14 (2 parts on backorder)
$269.70 updated 8/24/14 (removed fuse clips, added 2 new caps, 3 parts on backorder)
$269.70 updated 8/27/24 (4 parts on backorder)
$269.70 updated 9/1/14 (4 parts on backorder)
$269.90 updated 9/5/14 (4 parts on backorder)
$283.43 updated 9/10/14 (added 1 new cap, 5 parts on backorder)
$283.43 updated 9/12/14 (5 parts on backorder)
$310.43 updated 9/23/14 (added 1 new cap, 5 parts on backorder)
$310.68 updated 10/13/14 (7 parts on backorder)
$272.00 updated 10/27/14 (6 parts on backorder)
$277.00 updated 11/21/14 (3 parts on backorder)
$272.65 updated 12/10/14 (4 parts on backorder)
$272.81 updated 12/30/14 (3 parts on backorder)
$272.81 updated 1/19/15 (4 parts on backorder)
$272.81 updated 2/16/15 (4 parts on backorder)
$272.82 updated 3/27/15 (1 part on backorder)
$272.82 updated 4/27/15 (3 parts on backorder)
$272.82 updated 6/17/15 (1 part on backorder)
$272.82 updated 7/10/15 (1 part on backorder)
(http://www.sarversystems.com/components/com_remository_files/file_image_3/img_3_01.jpg)
(http://www.sarversystems.com/components/com_remository_files/file_image_4/img_4_01.jpg)
(http://www.sarversystems.com/components/com_remository_files/file_image_5/img_5_01.jpg)
(http://www.sarversystems.com/components/com_remository_files/file_image_6/th_6_01.jpg)
Here is the case shown above:
(http://www.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_18092.jpg)
http://www.harborfreight.com/multi-compartment-utility-box-40528.html (http://www.harborfreight.com/multi-compartment-utility-box-40528.html)
But here is a better alternative, since it is larger in size:
(http://www.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/i/m/image_22217.jpg)
http://www.harborfreight.com/toolbox-organizer-with-4-drawers-68238-8143.html (http://www.harborfreight.com/toolbox-organizer-with-4-drawers-68238-8143.html)
-
Electrohome monitors use pigtail GMA style 1.25 amp fuse for the B+ fuse. I replace it with two of Jameco Electronics # 119280 side terminal fuse clips. The circuit board already has the spots for the fuse clips. Makes replacing fuses a lot easier and cheaper.
Electrohome and several other monitors use a 2SD870 horizontal output transistor.
Wells K7000 uses a 2SD1398 for the horizontal output.
-
Based on the number of caps in the above list, how many of those parts you posted would you suggest having on hand? Obviously it would depend on how many of that particular monitor, but assuming it was an average mix of monitors....
-
I would keep a couple of the 2SD870 transistors on hand and a couple of the 2SD1398 on hand.
The fuse clips I like to keep 20 on hand. That will do 10 Electrohome G07 monitors.
-
I'll have to cross reference those to Mouser parts, I didn't see any of those 2 listed on their site.
-
for good measure through in the g07/08 flyback,and the 3pin regulator,
i know we are on topic about cap's,but a full rebuild demand's it
ed
-
Are those available from mouser though? I don't recall seeing any flybacks there.
Can you post a part number on the regulator? I don't have one in front of me at the moment.
-
a few places sell them
they are not adver's here so i dare not list them
google g07/go8 flyback's
it will get u to a www. under cup's
the reg i forget off of the top >ken please chime in<
+ add the horz freq tantalium..this is a common failure point in horz shift/hold/sync-lock-up
it is a small 1 4.7 or less at 16v and must be just about exact
ed
-
Can you post a part number on the regulator? I don't have one in front of me at the moment.
The Electrohome G07 regulator is a 2SC1106A.
Mouser generally does not carry Japanese semiconductor numbers (2SA, 2SB, 2SC, 2SD, etc), but they do carry American numbers (2N, 1N, etc).
For Japanese semiconductors you want to go to MCM Electronics.
-
Thank you both for the info.
I will update the list ASAP.
-
Ken: I'm still not getting any results on mouser searching for combination of 2NC1106A, 1NC1106A, 2SC1106A, or even 1106A. Could provide mouser part numbers, since you know those particular parts much better than I?
Ed12: How many of those caps would suggest adding to the list, based off the quantities of the other caps in the list? 4.7MFD @ 16V Tantalum. Is that a radial or axial package?
-
Type 2SC1106A has been obsolete for a long time. It is now very hard to find. It does cross to an NTE 94.
None of the major parts distributors carry the 2SC1106A any more.
-
No matches for NTE 94 either. Ugh. This is proving to be pretty difficult!
-
saver
there is 1 used per chassic
highly recmond u add it..it solves alot of horz problems
ed
-
Is it a radial or axial package?
-
radial
it is under the tin sheild
ed
-
10 of the tantalum caps have been added.
I still need part numbers for the fuses, clips, and transistors.
If someone can tell me the value of the fuse, I can cross reference it to a part number.
-
make sure u make note in there
the value must be dead on..
ed
-
Do you mean to just measure it before installing it? Or to just make the part ordered is the part ordered?
-
either
as a rule tan's do not :drift: until exposed to heat
but i tend to error on the safe side
and spec it to dead nut's as it were..
u have to under stand what it dose it >set's the horz freq and lock through a phase lock loop<..so bang on is better
ed
-
So it needs to be measured with a ESR meter?
-
tan's are 90% always right on.
but good measure say' yes when u are buying them..
to remove 1 and test it? it is a 50/50..no need to guess
btw the clip u are looking for is called a >s< clip for fuse's
what ken is refering to is u can put in a pigtail and or a blade type fuse
the board make's it that way,until latter on in the serial # run
rickn was the lead eng on the g07/go8 stuff
nice guy and is chatty when u ask him q's
ed
-
What value should the fuse be?
-
let me see if this will make it easier for u
btw there is 2 fuses used
1 is the main input fuse
the other is the b+ fuse
plus u might need a few resistor's,
these are 1 ohm job's and act as a fuse AFTER the flyback
ed
-
Fuses have been added.
-
oh btw
when they did the nla on the requlator
to3 style
we went to a plastic 1
i would need some byte's to dig out the info for u
ed
-
prices went up a smidge over the weekend. All caps are still in stock though!
-
I am still unable to located the following parts on Mouser, or anywhere else. If someone could post the part #, I'll get it added.
ITEMS TO BE ADDED
•5 2SD870 transistor <--- need part #
•5 2SD1398 transistor <--- need part #
-
Bob Roberts stocks the 2SD870 and 2SD1398:
http://homearcade.org/BBBB/parts.html#semiconductors (http://homearcade.org/BBBB/parts.html#semiconductors)
-
Cool, I'll update the list ASAP.
-
Mouser is saying these are compatible with the 2 power transistors.
511-2STF1550
http://www.mouser.com/ProductDetail/STMicroelectronics/2STF1550/?qs=%2fha2pyFaduiNgDmMT2bHla6bE372AY3LNuQFCvgjlxlhbSvNzlb8hg%3d%3d (http://www.mouser.com/ProductDetail/STMicroelectronics/2STF1550/?qs=%2fha2pyFaduiNgDmMT2bHla6bE372AY3LNuQFCvgjlxlhbSvNzlb8hg%3d%3d)
726-BC817K-40E6327
http://www.mouser.com/ProductDetail/Infineon/BC-817K-40-E6327/?qs=%2fha2pyFadugrTOFV51sTPMgipnvexUuvXCkrSblYotHURl196ZIQ3XTSvlsXHMqC (http://www.mouser.com/ProductDetail/Infineon/BC-817K-40-E6327/?qs=%2fha2pyFadugrTOFV51sTPMgipnvexUuvXCkrSblYotHURl196ZIQ3XTSvlsXHMqC)
Comments?
I don't have any of the originals in front of me, but both suggestions are SMD devices.
-
no home run them..sorry bud
try going to 2sc #'s in t03 pkg's
if u want i will dig my list out
here is what u need to rember must have interel damper diode and handle greater then 1600v
ed
-
I'm sure mouser has something, I'm just not having any luck cross referencing anything, and apparently neither is Mouser.
If they were truly obsolete, Bob would (rightfully so) be charging a fortune for them.
-
chk your pm
DO NOT POST THE LINK
some one here get's real pissie about it ....
ed
-
OK??? I don't want to know.
-
it carrys every part
inculding the horz freq coil for g07/8's >common fault< as it burns itself out
u will find your req,and horz out
in-stock
i get all my g07/g08/well's kit's from them
beat's bob prices hand's down
ed
-
Not sure if you want to update the list (perhaps do a seperate one) cause there are not items on backorder and it says they are about 18 weeks out.
-
I've been watching it near daily. I do notice items go on backorder every now and then, but they usually come off back order in a day or 2.
I'll continue to watch it and see if anything stays on backorder for more than a week. If it does, I'll swap that part out for a more readily available part.
Thanks you for noticing that, I'm glad to see people are using the list.
-
All parts are available again.
-
I'll be modifying the list in a day or 2 if those 2 parts are still on back order.
-
Can someone please verify for me which fuse clips to include in the above list?
http://www.mouser.com/ProductDetail/Littelfuse/01110501Z/?qs=sGAEpiMZZMuG%252bgnN5hGYGz%252b7t4SVwK3ZNIPvW%252bavkvQ%3d (http://www.mouser.com/ProductDetail/Littelfuse/01110501Z/?qs=sGAEpiMZZMuG%252bgnN5hGYGz%252b7t4SVwK3ZNIPvW%252bavkvQ%3d)
or
http://www.mouser.com/ProductDetail/Littelfuse/10207101009/?qs=sGAEpiMZZMuG%252bgnN5hGYG0u12dc35WuVZ36vyla8Ap8%3d (http://www.mouser.com/ProductDetail/Littelfuse/10207101009/?qs=sGAEpiMZZMuG%252bgnN5hGYG0u12dc35WuVZ36vyla8Ap8%3d)
I'm not sure of the orientation of the pins on the fuse clips because I don't have a monitor in front of me at the moment.
-
either
ed
-
Electrohome uses the side mount fuse clips.
-
Thanks ed.
I went by the Jameco part number listed above, and converted it to the Mouser part number.
-
Am I missing anything else in the list that you'd suggest?
I saw mention of 1ohm resistors, but I don't know the wattage, or how many to add to the list.
-
ya ken
but i have seen 07/08 with both foot print's
that is why i said either
ed
-
1 ohm 1/2-1watt wire would flame proff.
it is in fact a fuse for the secondary side of the flyback
there i believe is 2 of them >ken correct me here<
ed
-
Are we talking about one of these?
http://www.mouser.com/ProductDetail/Vishay-BC-Components/PR01000101008JA100/?qs=sGAEpiMZZMsPqMdJzcrNwqUl9GN6Ib%252bQTn6HJi%2f7pOQ%3d (http://www.mouser.com/ProductDetail/Vishay-BC-Components/PR01000101008JA100/?qs=sGAEpiMZZMsPqMdJzcrNwqUl9GN6Ib%252bQTn6HJi%2f7pOQ%3d)
-
perty much
it is metal film...make's it flame proff.
if u can find it in 1/2 watt even better
ed
-
Updated!
-
As you can see, I am slowly bringing on other individual kits as well.
I'll update the lists to include part numbers, location on the chassis, and whatever other info is needed.
I hope I'm not stepping on anyone's toes by doing this, but I didn't see any other up-to-date posts for this.
-
I just ordered the bulk kit for myself. I'll take some pics and post them when I receive them.
-
The fuse clips are incorrect. Please adjust your cart accordingly until I can get it fixed.
-
I added 2 parts to the list.
33uf @ 35V, and 4.7uf @ 250V.
-
where did you buy your case/holder for all the capasitors? it looks really cool.
-
I would go with this: http://www.harborfreight.com/toolbox-organizer-with-4-drawers-68238-8143.html (http://www.harborfreight.com/toolbox-organizer-with-4-drawers-68238-8143.html)
Or with this: http://www.harborfreight.com/multi-compartment-utility-box-40528.html (http://www.harborfreight.com/multi-compartment-utility-box-40528.html)
I had to bend the leads on the larger caps to get them to fit in the compartments on the smaller organizer, but nothing major.
-
I'm going to swap out those 3 parts that seem to always be on BO for the next update.