Main > Monitor/Video Forum
Mouser Cap Lists
SirPeale:
--- Quote from: guppy on June 30, 2010, 01:40:51 pm ---
--- Quote from: SirPeale on June 23, 2010, 09:53:19 pm ---Updated the 4900 list above.
Location Voltage Value Notes?
C201 25 1000 Bumped up voltage from 16 to 25 647-UVZ1E102MPD
C205 16 470 647-UHE1C471MPD
C301 50 330 647-UVZ1H331MPD
C303 50 3.3 647-UVZ1H3R3MDD1TD
C308 50 3.3 647-UVZ1H3R3MDD1TD
C310 160 10 Bumped up voltage from 100 to 160 647-UVZ2C100MPD
C311 160 10 647-UVZ2C100MPD
C313 200 47 Bumped up voltage from 160 to 200 667-EEU-EB2D470
C315 50 1 667-ECE-A1HKG010
C351 50 1 667-ECE-A1HKG010
C352 25 47 647-UPM1E470MED1TD
C354 25 47 647-UPM1E470MED1TD
C366 25 22 647-UVZ1E220MDD
C505 200 560 661-EKMQ201VN561MP30
C506 160 22 661-EKXG161ETD220MJ2
C507 200 47 Bumped up voltage from 160 to 200 667-EEU-EB2D470
C701 25 1000 647-UVZ1E102MPD
C702 160 10 Bumped up voltage from 100 to 160 647-UVZ2C100MPD
--- End quote ---
I ordered and installed this kit (I used your mouser project list) on my 19K4952 Wells-Garner . The C505 cap (mouser# 661-EKMQ201VN561MP30) is physically much smaller than the original cap. Therefore the heavy pins on the mouser cap will not align to the holes in the pcb. The pins on the mouser cap are les than 1/4" long, so there is no bending possible. I ended up just not using it at all. This single cap is also the most expensive in the kit ($2.13).
BTW, My monitor looks great now. Thanks
--- End quote ---
I hadn't needed the K900 list above until now, and there are some discrepancies. I must have used another revision of the schematics to put the list together. Here are the discrepancies:
C303 - 2.2uf @ 50V
C308 - 2.2uf @ 50V
C311 - 4.7uf @ 160V
C313 - 100uf @ 160V
Guppy, if you're still around, can you detail which 4900 model you have?
deega:
Does anyone have an updated project for a WG-K4600? Several items in the posted project are back-ordered.
Thanks!
SirPeale:
--- Quote from: deega on November 24, 2010, 08:20:13 pm ---Does anyone have an updated project for a WG-K4600? Several items in the posted project are back-ordered.
Thanks!
--- End quote ---
When this happens I search for products based on the same parameters of the original, then select one that's actually in-stock. Should take you just a few minutes to pick them out.
deega:
That's what I did.. I'm awaiting my order now.
I also double checked my caps in my chassis to confirm and it appears that one of the two 2.2uF 50v is supposed to be bipolar. C633, at least on my board, is a bipolar cap. I ordered 647-UEP1H2R2MDD as a replacement for that one.
I'll know more when I receive my order. :) Thanks for the mouser projects!
smalltownguy:
The K7400 cap list over at mouser had some end of life caps on it with zero quantities left, so I made a few substitutions and re-saved the list:
http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=66CFEEEB31
I see a few that I selected are also EOL too, but they're leaded caps with some pretty good quantities left, so hopefully the list can remain 'as is' for now.
Thanks....
-STG
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version