Main > Buy/Sell/Trade - non-retail
Testing waters ... Interest in CP blanks for Lindstrom plans (Pac Cocktail 11")?
(1/2) > >>
Curbfeeler:
I've made some calls, and I'm about to buy the materials to make a few Bally cocktail control panel blanks.  I'll be making out of aluminum .05 stock which is equiv to the original 16ga Bally CP material, except the originals were hardened steel.  I have no way to cut/drill/bend the steel, so I'm going with aluminum.  For a CP that's only 11" wide it will be plenty strong enough for game play.

My thought is that if there is interest from some of you out there that I would just make a run of these and sell for 20 dollars/set plus actual shipping.  A set of blanks on the internet currently runs 60 dollars.

Let me know here or PM if this is something some of you would like to see.  My cab is an original Pac cocktail, so I'd be using an original as a template and making to exact size.  They would fit Kyle Lindstrom's plans as well, of course.

Dan
matman:
Funny, I'm attempting the same thing.  Except all I have is Kyle's plans to go by, no originals.  I picked up a sheet from the hardware store for $20 (16Ga aluminum) that should cover both sides.  My plan was to use a 5/16" router bit along an edge of a 2X4 and use that as my curve to bend along from within a vise (or with another 2X4 on the other side screwed together).

I'm not exactly sure how i plan to cut it.  Coincidentally, i was just looking at the plans 2 minutes ago and was trying to figure out the support underneath(inside?) the cp "steel" (Item 16) - that piece confuses me, but I wonder with aluminum it will require better or increased support from the original plans?

Is your plan to just paint them black?

Matt
BASS!:
c'mon if your going to custom make a panel out of metal, at least check in to powder coating:-)
Curbfeeler:
Yes, I was just planning to prime and paint with the rustoleum satin black, which by most accounts is dead on the original bally.

As far as cutting, you can reverse the blade on your table saw and set the depth of your blade to just above the thickness of the alum.  That should get through this material and give a nice edge.  the table saw blade will tear/rip too much as-is and may melt.  I have the ability to set RPM on my table saw which will help, but most don't.  You can also use a scroll saw with a sheet metal blade, but you'd want to make sure you clamp down and follow a straight edge (see sticky in woodworking section) as scroll saw on metal is just asking for wavy cuts.

I've got a contractor who has built room additions for me, and we have a good relationship.  He's agreed to bend for me on his $3000 alum brake which is a must for this job.  I don't think you'll have luck hand bending this material with the old "hammer and a 2x4" method or any other manual method I can think of.

As for strength, I think the alum will be fine with no backing.  We're talking about joystick use and pushing buttons.  An 11" wide piece of alum will not need any kind of additional reinforcement.  IMHO, of course.

I figure I'll spend 60-70 on raw materials and will need to pay my guy 50 for the bending.  From that I think I can yield 10 or so CP. I'm hoping that if I sold a handful at $20 per set then I could defer a lot of my cost and everyone could benefit.  A powder coat might not be bad, but I'd need to price it and see what it adds per-unit.  My guess is nobody is interested above $30 shipped but may be wrong.

Good luck to all.  Let me know if I'm hitting on something people are interested in.  I may proceed anyway, just to see what I get.
dan



Popcorrin:
Definitely interested.

The only problem is that aluminum can be difficult to get paint to stick to.  Etching primer is a necessity, but even with etching primer I haven't always been 100% successful getting the paint to stick.
Navigation
Message Index
Next page

Go to full version