Main > Project Announcements
Bella's Arcade [FINISHED]
javeryh:
Last update before the holidays!!
The bezel panel has finally been cut to size and it fits in place rather nicely (I still have to glue everything though). So far this has been the craziest piece I've cut due to the fact that I had to make 3 rabbet cuts in addition to cutting a notch in the rear for the speaker and marquee light wires to pass through. Also, this is a great excuse to show how the control panel will look once it is installed and explain how I made room for the black cardboard bezel which will eventually surround the monitor and the glass that goes on top. I think it came out pretty good!
The following is a shot of the rear of the bezel panel showing the notch I cut for the wires. I just used my jigsaw to cut the notch freehand. I am going to be installing an additional panel between the marquee bottom panel and the bezel panel that will go in front of the wires and cover the notch.
A while back I installed strips of pine on the interior of the cabinet so I would have a place to rest the bezel panel (which is also on the same plane as the control panel). However, after assembling the cabinet and placing a sheet of MDF in place where the bezel panel and control panel would go I realized that I hadn't allowed space for the black cardboard bezel and glass that would eventually cover the monitor.
My solution for this was to cut a 3/8" rabbet on the sides on the bottom of the panel. This would allow the bezel panel to sit 3/8" lower than I had originally anticipated. However, since I didn't want the control panel to sit lower as well I created a 3/8" rabbet on the top of the bezel panel that the control panel could rest on. This would also create a lip between the control panel and the bezel panel so the black cardboard bezel and glass had a place to sit and the entire thing would be flush when finished. The picture below is a mock-up of what I am trying to accomplish.
As you can see, I am going to use the control panel as a lip for the glass and cardboard bezel to rest on. Once they are installed the entire surface should be uniform.
The next pictures show how I cut the bezel panel. The close-ups are of the side showing the rabbet cut which allows the panel to sit 3/8" lower than I had originally planned (creating the space for the cardboard bezel and glass).
The next picture is a close-up of the front of the bezel panel with the rabbit I made in the front which the control panel will sit on. It is also 3/8" deep and as you can see removing 3/8" from the top and bottom of a 3/4" sheet of MDF completely removes the corners. This gap will be covered though so it's not a problem or anything.
The next picture shows the front rabbet across the width of the cabinet.
Finally, these last shots show what the final installed control panel will look like as well as the lip that will support the cardboard bezel and glass that covers the monitor.
Thanks for looking!!
theCoder:
I see your project has the infamous "weird angled joint". I think every cab projects have at least one of these.
What did you use to make the rabbit cuts? Router or table saw?
Great progress.
javeryh:
--- Quote from: theCoder on December 22, 2006, 11:30:48 am ---I see your project has the infamous "weird angled joint". I think every cab projects have at least one of these.
What did you use to make the rabbit cuts? Router or table saw?
Great progress.
--- End quote ---
Thanks!
I hate that weird angle joint! It's the last thing I have to cut before I can call the construction complete and start the finishing process. I really need to set up my table saw.
I used my trusty router, straightedge and a dado bit to make the rabbet cuts. It took a while (I nibbled 1/8" of the material away at a time and had to make 3 passes on each rabbet to get to a 3/8" depth) but everything came out nice and even. I wish I could use a router to make the weird angle cut too!
I'm hoping that next week I will start finishing the cabinet. My wife and kid will be at her parents house as a little extension to the holidays (I have to work next week). I need to pick up the primer/sealant and buy the pink paint, sandpaper and possibly a sprayer.
theCoder:
--- Quote from: javeryh on December 22, 2006, 12:20:53 pm ---I'm hoping that next week I will start finishing the cabinet.
--- End quote ---
I'm pretty much at the same point on my project as well. I'm not looking forward to painting in the winter. It's cold & rainy where I live. Oh, well.
javeryh:
OK, minor update for something major to the project.... the marquee has been ordered!!
The total cost came to $58.93 with shipping. The marquee was $15.95 and I also ordered plexiglass cut to size for $24.99 and an upgrade to the "Ultimate" style material for an extra $10.00. Shipping was $7.99.
Overall, I think it's a little pricey but I also think it will be worth it in the long run. I've heard nothing but praise from everyone who uses mamemarquees so I'm excited to see the final product.
Here's the final design of the marquee - sized properly to 6.5" tall by 18.5" wide and leaving a 0.75" edge on the top and bottom to accomodate the marquee retainer that will be used to hold it in place.
Oh yeah, I almost forgot - a HUGE THANK YOU to megashock for designing this awesome piece of art and putting up with me through all of the minor tweaking I had him do. I am very very pleased with how this came out.
Thanks!!
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version