Main > Project Announcements
Bella's Arcade [FINISHED]
Pongo:
Glad you like them,... looks like the color matches pretty well too.
To answer the questions about where to get the vinyl stickers, I will offer this shameless plug.
http://forum.arcadecontrols.com/index.php?topic=64645.0
javeryh:
--- Quote from: pkellum on January 30, 2008, 06:17:33 am ---This is a very nice cabinet! Thanks to this project, I'm already putting together ideas for a cabinet for my son, 3 years old next week :) The Player 1/2 buttons are just too cute, I love them :cheers:
One suggestion, while reading through this thread and the blog I began to realize how much of the story about the cabinet has played out in them and I thought it would be a wonderful keepsake for your daughter when she's older. Have you considered printing out the blog and perhaps the thread and having them bound into a booklet once you finish the cabinet? You could place them in an envelop inside the cabinet for her to discover when she's older.
Having them bound would be just a few dollars at someplace like Staples or Kinko's, not as expensive as it was in the old days.
Just an idea :)
--- End quote ---
Thanks! That's actually a pretty cool idea. I'm just hoping she comes to appreciate it eventually.
Also, I'd be happy to answer any questions you might have when you start building the cabinet for your son.
--- Quote from: Franco B on January 30, 2008, 05:33:43 pm ---Awesome fella, the decals really set it off nicely 8)
--- End quote ---
Thanks. They look even better in person and really add a finishing touch. The more details the more it looks like it came from a factory or something.
--- Quote from: Pongo on January 31, 2008, 08:58:01 pm ---Glad you like them,... looks like the color matches pretty well too.
--- End quote ---
Yup. It's almost a perfect match to the t-molding! You really can't tell any difference unless you are looking for one. Thanks again!
javeryh:
This is it! The final actual physical construction on the cabinet. It's about time.
One last thing that had been bothering me was the fact that I had to open the coin door to hit the power switch on the computer in order to turn everything on and off. I decided to relocate the power button from the front of my computer to the rear panel on the outside. It's out of sight but easy enough to press before and after a play session.
One consideration was that I wanted the button to be recessed in the panel - I think it looks nicer and whatever small chance there is that it will get pressed accidentally is greatly reduced. I had to come to terms with drilling through my awesome finish on the rear panel - oh well, it was necessary I guess.
Anyway, I wasn't sure about the placement of the button so I actually thought about it for quite some time. I wanted it to be out of the way, easily accessible and aesthetically pleasing in it's ultimate location. I think I achieved all three of these things. I decided to place the button towards the top of the cabinet because it would be easiest to press in that location.
The first thing I did was lay out the center for the button hole using some painter's tape (so as not to mark up the actual cabinet. I measured in from the right to the exact center of the power plug to line up the button hole (for aesthetics) and then measured down from the top the same distance and made a mark and tapped out the center with an awl:
Next, I drilled out the hole in two steps using forstner bits. The first one - 7/8" - was just larger than the overall diameter of the button at it's widest point and the second one - 1/2" - was the exact size you would drill if you were installing the button normally. Here is the resulting hole:
You can see the two different diameter holes here quite easily. Once installed, the button will be flush with the back panel. Next came the tricky part - wiring it up. I had to cut the two wires from the button on the computer case and splice in the two wires from the new button. Easier said than done due to the location of the button - I had to remove the marquee and feed the wires through the same narrow hole that the power cord from the marquee light was in. This took me almost an hour of trial and error until I finally got them in there. Check it out (also notice that I painted the inside of the hole because I'm super anal):
...and here's the button all wired up but not installed:
Here's the finished installation:
I am VERY happy with the way this worked out. The button is very easy to reach and it looks great - everything is tied into it. You press it once and the computer powers on, the marquee light comes on, the speakers power on and the LED coin door lights light up. The computer boots straight to whatever the last game played was. Press it again and everything shuts down. This definitely beats opening up the coin door and contorting my hand to reach the power button on the computer!
Only 3 or 4 more posts and I swear I'm done!! :cheers:
Anubis_au:
Even the connector clips are pink...
One super build. And probably the most thoroughly documented build ever!
:cheers:
Avrus:
I would have thought for SURE you would have gone for one of these:
http://www.performance-pcs.com/catalog/index.php?main_page=product_info&products_id=22361
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version