Main > Main Forum

Routing For J-Stick

Pages: << < (3/4) > >>

JoshuaMiller:


--- Quote from: Timoe on July 24, 2006, 08:51:26 pm ---Here is a pic of a Jstick mounted under 5/8" MDF and 1/8" Plexi.  I routed out the bottom leaving just the exact thickness of my Tnuts (3/8" or less).

It is solid and still has good stick height.

--- End quote ---

thanks a lot, man!

--Joshua--


Minwah:


--- Quote from: JoshuaMiller on July 24, 2006, 07:39:23 pm ---Thank you.  I hate to impose after you were kind enough to reply, but do you happen to have a photo of how tall the stick is with your 4mm routing job?  I'm having a hard time visualizing how much I'm going to lose by mounting it below.  Did you have a sheet of plexiglass on your CP, or did you use something else?

--- End quote ---

I don't have a pic to hand with the panel routed, but on this page (about half way down) there are some pics of a panel I used previously.  This is 15mm (~5/8") MDF, NOT routed.  So if you can imagine the sticks poking out 11mm more....

http://forum.arcadecontrols.com/index.php?topic=18812.40

I do not have a sheet of plexi, I will be using a CPO (when I've designed it!).

Edit: I think I should have a pic at home of the new routed panel, so I'll try to find that tonight...

JoshuaMiller:


--- Quote from: Minwah on July 25, 2006, 05:34:29 am ---
--- Quote from: JoshuaMiller on July 24, 2006, 07:39:23 pm ---Thank you.  I hate to impose after you were kind enough to reply, but do you happen to have a photo of how tall the stick is with your 4mm routing job?  I'm having a hard time visualizing how much I'm going to lose by mounting it below.  Did you have a sheet of plexiglass on your CP, or did you use something else?

--- End quote ---

I don't have a pic to hand with the panel routed, but on this page (about half way down) there are some pics of a panel I used previously.  This is 15mm (~5/8") MDF, NOT routed.  So if you can imagine the sticks poking out 11mm more....

http://forum.arcadecontrols.com/index.php?topic=18812.40

I do not have a sheet of plexi, I will be using a CPO (when I've designed it!).

Edit: I think I should have a pic at home of the new routed panel, so I'll try to find that tonight...

--- End quote ---


Thanks, Your Cab looks Great!

--Joshua--

JoshuaMiller:

New Question-

How did you guys mount the sticks from below without showing mounting bolts on the top of the CP?  How can I attach the sticks to such a thin amount of wood and have it be solid?

Thanks for all of your help-

--Joshua--

97thruhiker:

Not sure on the thickness of your wood panel but you should not have any problem mounting a "J" Stick.  In my mame cabinet (3/4 inch) I just routed a square roughly a little bigger then the footprint and it worked fine.  On the Donkey Kong Cabinet I just finished I did not route the panel.  The picture shows 1/2 MDF, two layers of laminate (to get the desired 9/16 thickness for the t-molding), lexan control panel overlay (I'd guess a millimeter thick), and the dust washer.  It feels perfect in my opinion.  As far as mounting I just countersunk carraige bolts into the MDF below the layers of laminate.  Good luck, I really like the "J' stik and if you are looking for colors other then red check out Lizard Lick Amusements.  I got great customer service from them.  The $19 one is the same as the "J" Stik.

http://www.lizardlickamusements.com/pages/joysticks.shtml

Pages: << < (3/4) > >>

Go to full version