Main > Main Forum
ATX power supply, no mobo, momentary switch question
(1/4) > >>
quarterback:
Okay, we all know that ATX power supplies want to be hooked up to a mother board in order to turn on.  When you hit the momentary switch on your PC's case, it sends a signal to the mobo which, effectively, shorts a couple pins on the PS connector and it turns on.

If you're running an ATX power supply withOUT a mobo, you can manually short these two pins together and the PS will turn on.

However, I'm not sure if this will accomplish what I want and I'm hoping that somebody here can tell me how to do what I'm looking for.

I'm not using a motherboard.  I want to use a power supply that has a momentary switch so, when power is removed from the PS (IOW, the AC power goes out) and then is REapplied (IOW the AC power comes back on) the Power Supply does NOT power back up.

Unlike an ATX supply, in an AT power supply the switch actually controls the flow of power.   So if the switch is left "On" then cutting/reapplying AC power just turns the PS on and off without any more touching of the switch.  I do NOT want this.  I want the opposite of this.

If the ATX was hooked up to a mobo, this wouldn't be a problem.  But I believe that jumping the two pins on the cable will cause the ATX to act in the same manner as the AT, and I don't want it to.  I do not want it to restart after AC power has gone off and then come back on.

Any thoughts on how to accomplish this?
Thanks
M3talhead:
Going off my years as an expert satellite electrican, I can tell you you'll need an avocado, a hampster, 3 flux capacitors, and duct tape. :police:




....though I'm not sure what species of hampster you'll actually need.
SteveJ34:
What's the application for the use of the standalone PS?

Only thing that comes to mind is the use of a Relay switch that in turn will need to be controlled by another source that *does* exhibit the "Do Not Power On when Power is Restored" functionality.

1. If this PS is in a cab that also has a PC which is operating in a manner that you want, ie: no power on when power is restored

 and

2. it fits your design for the secondary ATX PS to be controlled by the first

then you can use a relay switch that is controlled by the 12 volt line from the first PC Power Supply that in turn jumps the pins in the secondary PS to power it on.

As many others have done, I created a single switch power up in this manner using a relay in place of the toggle switch in a power strip.

Such a relay could act as a switch for most anything.....I picked up one at Radio Shack that is rated up to 20amp, 250v IIRC.

I trust the above makes some sense....

quarterback:

--- Quote from: SteveJ34 on August 19, 2005, 03:32:58 pm ---What's the application for the use of the standalone PS?
--- End quote ---

Without getting too complicated, it's to create a regulated 12v DC (and 5v) power source in my car to power an LCD.

Car 12v is crazy all over the place (7v to 15v to who knows what) and while getting a DC->DC regulator is possible and more energy efficient, it's also more expensive and more limited in functionality.    So my plan is to hook up a power inverter to my car's 12v DC, plug in a mini ATX power supply and grab the stable 12 volts off of that.

That setup will work, but what I would really like is to take advantage of the momentary power switch function of ATX.  That way I'll never subject the PS (or anything attached to it) to an on->off->on surge cycle that can happen when you first start your car.   If the PS automatically switches itself to "off" when the car is shut down, then I'll have to manually turn it on after I start the car.  This is the end result I'm hoping for.

Thanks
SteveJ34:
Ah, makes sense.

I guess parts like this

http://tinyurl.com/adoyq

are already expecting the incoming 12V to be regulated and don't include the regulator circuitry you would find in an actual DC-DC regulator?

Or what about this: http://tinyurl.com/9zgm9

Doesn't that accomplish what you're after at least for a single 12v circuit?

If yes, I guess you might need more than one to also get the regulated 5v out you want as well.


Navigation
Message Index
Next page

Go to full version