Main > Main Forum

Counter-sink v.s. double drilling.

Pages: << < (2/3) > >>

DrewKaree:

Something that happens all too frequently when not using a countersink bit is described in detail, although the effort when taking into account all the screws you are going to put in this machine was WAY glossed over, and no one else commented on, was stated here:


--- Quote from: mjrsting on January 24, 2005, 10:07:39 pm ---
I got about the same results, though without the coutersink hole, it did "frey" the edges a bit.  My solution for that was to put the screw partially in, cut off the frey with a utility knife blade, and then finish screwing it in and sink the head.  I puttied over the screw head and it all was good.  Saved a lot of time vs. using a countersink bit.


--- End quote ---

Now, color me ignorant here, but screwing in the screw partially, cutting off the frayed crap that will happen, and not gouging out crap you DON'T need to be taking off, and then completing the screwing in of the thing seems to be more work than using a countersink bit. 

Part of that "ignorance" probably comes from thinking you are using the right tool for the job.  I'll provide you with a picture for this, as it seems you spent money on a tool that works fine, but if you had spent a few more bucks, would have gotten you the tool that is SPECIFIC for your use, and PERFECT in its job of saving you time and giving you a neater appearance.

The thing you want it this here:


If that one's too expensive, Home Depot will sell one of several quick-change countersink/screwdriver sets, and all you have to do is buy the screw tip you need and swap it out if the standard #2 phillips bit isn't what you want.  They'll sell either a DeWalt, Ryobi, Bosch, or Milwaukee brand, or perhaps all of 'em at once.  This thing is EXACTLY what you want, and will eliminate you sittingthere with a friggen utility knife cutting wood by hand, when you should be doing it with *insert Tim "The Toolman" Taylor voice* - MORE POWER!

GameOver:

I double drilled, not as bad/time consuming as it sounds if you work smart.

Mameotron:

Or, you could drill your pilot holes and countersink... (Toolman voice) AT THE SAME TIME!! :o :o

http://www.grizzly.com/products/item.cfm?itemnumber=G2570

(lots of manly grunting) :laugh: :laugh:

DrewKaree:

Here you go.  An image of the version you can pick up at HomeDepot, Lowes, Ace Hardware, Menards, or whatever home improvement store is near you.  I even found a UK example, so you folks aren't off the hook here.  THIS is the cheaper version of the Insty-Bit system I showed above - should run you $6-13, depending on the manufacturer and the included screwdirver tips.  The Bosch version at Home Depot includes 2 different straight bits, 3 different phillips bits, and 4 square bits.


This SHOULD be the standard for our hobby.....you can change from drilling the pilot hole w/countersink to driving the screw in less than 5 seconds flat.  Now STOP all this nonsense about using two drill bits!

GameOver:

 8)Oh good...pictures!

Hear ye...hear ye!  Let it be known that standard 2.4.6a of the cab builders association of da wurld will from here on out be known as the DK 5.0 standard.  Simply stated, if you use the proper tools & can sink & counter sink a screw into a cab in under 5 secs, you've DK'd it.

I got one of those counter sink jobbers - it broke on the first hole!  Guess it was a bad batch, or maybe I put it onj backwards.  2 drill bits after that.  Besides, the brief intermission while changing bits gives you opportunities

1)  Partake in your favorite beverage
2)  light up a smoke (I've since quit, but still an option)
3)  yell at the dog
4)  take a johnny break
5)  partake in your favorite beverage

Pages: << < (2/3) > >>

Go to full version