| Main > Main Forum |
| I'll be todays vidiot: # of spinners on a minipac? |
| << < (2/2) |
| u_rebelscum:
--- Quote from: Tiger-Heli on August 14, 2004, 05:31:47 pm --- --- Quote from: Tweaked on August 14, 2004, 05:08:14 pm ---I read the minipac can control spinners and I am a huge fan of super offroad and super sprint and the spinning steering wheels... What I need to know is how many spinners (spinning steering wheels) I can put on a Minipac --- End quote --- Two - but they will have to be connected as Trackball Y and Trackball X and you will probably need MAME Analog + to get them working together. --- End quote --- Official mame starting with 0.85 (0.84u5, actually) can remap mouse axis. |
| Tiger-Heli:
--- Quote from: Tweaked on August 14, 2004, 05:59:17 pm ---What I was looking at was using 2 minipacs like: minipac 1: player1 with all associated buttons Player2 with all associated buttons trackball minipac2 or ipac2: player3 wtih all associated buttons Player4 with all associated buttons spinner1 spinner2 --- End quote --- I may have steered you wrong with my initial reply. According to this thread: http://www.arcadecontrols.org/yabbse/index.php?board=1;action=display;threadid=23042 Andy Warne said that there is no difference between the Mini-Pac boards themselves. That implies that (if you made your own harnesses out of an IDE cable), you could buy two of the $29 standard mini-pacs and basically have an I-PAC/4 and an Opti-PAC for less money than an I-PAC/4 alone. I would prefer someone who bought the $29 board to test the trackball interface before I tried this, though. There also was that thread about someone having trouble getting the two mini-pacs to stay programmed, but that shouldn't be a problem. |
| Bgnome:
if you dont mind sharing axes, you could fit 2 more spinners or another trackball.. |
| Tiger-Heli:
--- Quote from: Tiger-Heli on August 16, 2004, 05:13:02 pm --- --- Quote from: Tweaked on August 14, 2004, 05:59:17 pm ---What I was looking at was using 2 minipacs like: minipac 1: player1 with all associated buttons Player2 with all associated buttons trackball minipac2 or ipac2: player3 wtih all associated buttons Player4 with all associated buttons spinner1 spinner2 --- End quote --- I may have steered you wrong with my initial reply. According to this thread: --- End quote --- Confirmed, I did steer you wrong on this. Your initial idea was a good one. --- Quote ---Andy Warne said that there is no difference between the Mini-Pac boards themselves. That implies that (if you made your own harnesses out of an IDE cable), you could buy two of the $29 standard mini-pacs and basically have an I-PAC/4 and an Opti-PAC for less money than an I-PAC/4 alone. --- End quote --- I have confirmed this to be the case. --- Quote ---There also was that thread about someone having trouble getting the two mini-pacs to stay programmed, but that shouldn't be a problem. --- End quote --- This has also been resolved, AFAICT. Be advised, what you will have to is the following: 1) Plug in Minipac 1 - Program for your Player 1 and 2 inputs - Unplug Minipac 1. 2) Plug in Minipac 2 - Program for your Player 3 and 4 inputs. 3) Plug Minipac 1 back in - No further programming required. |
| microwrx:
Depending on where you locate the Mini-PACs themselves, if you have your cab setup like most with players 1&2 in the middle and you are going to program both Mini-PAC's anyway I'd suggest you have one as player 1/player 3 and the other as player2/player 4. It's a bit of a stretch between player 3 & 4 is all. Again, it all depends on how you're going to do your wiring etc. though. |
| Navigation |
| Message Index |
| Previous page |