Main > Main Forum
Buttons Sticking...
DougHillman:
While it may not be the root of DeathMonk's button sticking problem, one way to keep lexan alignment problems from cropping up is to drill it at the same time as you do the CP.
The best way to do this is to use 2 pieces of wood with the lexan sandwiched between them. One piece of scrap and your actual CP. This not only gets you exactly lined up holes, but helps keep the lexan from cracking or scarring.
Santoro:
--- Quote from: DougHillman on March 18, 2004, 06:41:45 pm ---While it may not be the root of DeathMonk's button sticking problem, one way to keep lexan alignment problems from cropping up is to drill it at the same time as you do the CP.
The best way to do this is to use 2 pieces of wood with the lexan sandwiched between them. One piece of scrap and your actual CP. This not only gets you exactly lined up holes, but helps keep the lexan from cracking or scarring.
--- End quote ---
yeah, where were you six months ago? ;D I am going to do this next time. Good suggestion.
RandyT:
Here's another tip if you have a router. This also works if you want to add a plastic overlay to a panel that has been cut already.
If you haven't already, do all the work you need to on your panel, including all the holes and the outside edge.
Leave the protective film on the Lexan, acrylic, whathaveyou.
Clamp the plastic securely to the face of the wood. Make sure it can't move!
Flip over the panel and drill a pilot hole large enough for your router bit from the bottom side of the panel (keep them toward the center of your holes)
Place a laminate trimmer bit in your router and adjust the plunge/depth so that the bearing rides on the inside wood wall and clears the thickness of the plastic.
Place the router bit through the pilot hole, switch it on and carefuly follow the contour of the wood.
If you adjusted the depth properly, the bearing will make sure everything stays true to the wood.
Do this for every hole.
Now install about 4 buttons into the holes toward the center of the panel and tighten the nuts well. This will hold the plastic in place for the final cut.
When you are satisfied that the buttons are holding everything in place, and they won't interfere with the path of the router, use the same bit to cut around the outside contour of the panel.
Remove the buttons and peel the protective paper from the plastic. If all went well, you should now have a nice, clean plastic overlay that pretty exactly matches your wooden panel.
But as with everything, YMMV. ;)
RandyT
OSCAR:
I agree with Randy, the best way to cut plexi is with a router. I do it a little bit differently than Randy suggested, tho. I try to drill plexi as little as possible... if you are not careful, the pressure from the bit can cause it to crack because you can press a lot harder with the drill than the bit can remove material. Plexi does not respond well to a point pressure like you can induce with a drill bit. If you have to drill plexi, do it slow so the material is removed before you try to force the bit through it.
What I do is use a template bit, not a laminate bit. The difference is that the bearing is above the cutter head on a template bit so you don't have to drill pilot holes. With a template bit, I plunge directly into plexi without a pilot hole. I've built many panels this way and have never cracked a piece of plexi.
First I drill out all the holes in the wood, then clamp or screw the plexi directly to the wood. Then I flip the control panel over so the plexi is on the bottom. So now the holes in the wood are the template for the plexi holes. Pics of the results of this method can be seen on my multi-williams project page, http://www.oscarcontrols.com/sinistar. That page also shows how I used a c'sink bit to drill countersinks into the plexi so flat head screws can be used to hold it down, because my overlay on that project actually goes on top of the plexi. The purpose of the plexi on that cp was actually so the joystick dustcovers and tee-nuts could be recessed without anything showing from the topside for a totally clean overlay surface.
krick:
A tip for drilling plexi courtesy of those guys who put windows in their computer cases...
Take a cheap drill bit of the desired size and drill it into concrete first to dull the tip.
Now when you drill into the plexi, it won't grab and crack the plastic, it will just get hot from friction and melt through.