Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Ledblinky - How to ignore a led controller?  (Read 12170 times)

0 Members and 1 Guest are viewing this topic.

Student123

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:October 14, 2024, 10:26:16 am
  • I want to build my own arcade controls!
Ledblinky - How to ignore a led controller?
« on: December 22, 2023, 10:33:46 am »
Hi,

I have 3 led controllers: Pac-Drive, IpacUltimate and another IpackUltimate. I have my coin door lights hooked up to my pac drive, used to run perfectly, but since I installed ledblinky it takes charge of all the controllers and it shuts it down.

Any way to ignore a controller or have lights on all the time regardless if hyperspin is running or not? Just want the Leds from that controller to light as soon as the pc starts.

Thank you!!

PL1

  • Global Moderator
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9504
  • Last login:Today at 01:40:53 am
  • Designated spam hunter
Re: Ledblinky - How to ignore a led controller?
« Reply #1 on: December 22, 2023, 12:06:59 pm »
Any way to ignore a controller or have lights on all the time regardless if hyperspin is running or not? Just want the Leds from that controller to light as soon as the pc starts.
If you want those lights to be always-on when the PC is on, remove the controller and power them directly from a drive power Molex connector.
- No animation = no need for a controller.   :cheers:


Scott

Student123

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:October 14, 2024, 10:26:16 am
  • I want to build my own arcade controls!
Re: Ledblinky - How to ignore a led controller?
« Reply #2 on: December 22, 2023, 01:20:52 pm »
Hi Scott,

Yes, thank you, the controller makes it easier to setup and maintain.

Much cleaner solution then using amolex directly to the lights.

Is there no alternative to have ledblinky bypass a controller or ignore it?

Thanks

PL1

  • Global Moderator
  • Trade Count: (+1)
  • Full Member
  • *****
  • Offline Offline
  • Posts: 9504
  • Last login:Today at 01:40:53 am
  • Designated spam hunter
Re: Ledblinky - How to ignore a led controller?
« Reply #3 on: December 22, 2023, 05:13:38 pm »
the controller makes it easier to setup and maintain.
. . . except for the software . . .  :lol

Much cleaner solution then using amolex directly to the lights.
Consider using a euro-style terminal strip for LED power distribution like mcseforsale did with his Blue Pill build.

http://forum.arcadecontrols.com/index.php/topic,117977.msg1266787.html#msg1266787






Scott

Student123

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:October 14, 2024, 10:26:16 am
  • I want to build my own arcade controls!
Re: Ledblinky - How to ignore a led controller?
« Reply #4 on: December 22, 2023, 06:31:50 pm »
Thanks, will look into it!

Student123

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 18
  • Last login:October 14, 2024, 10:26:16 am
  • I want to build my own arcade controls!
Re: Ledblinky - How to ignore a led controller?
« Reply #5 on: December 23, 2023, 04:03:18 am »
Found a solution, it works so the coindoor stay lit when Hyperspin starts, good enough :)


1: Open LedblinkyAnimation Editor , go into file and select LED Controller Independant.
2: Create a  new animation with just the lights on for your coindoor and save it. I named it "Coindoor".
3: Open LedblinkyConfig.exe go into the Misc Options tab, enable cabinet leds, put in the type of controller and its ID on my case for a PacDrive it was PD1, under each tab below select the new animation you created above and save.

This will Light the coindoor each time you open Hyperspin as a separate animation."