Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

« previous next »
Pages: 1 [2]  All
  
Go Down

Author Topic: Hantarex Polo/2 25-28 Dead - how to test B+ (SOLVED)  (Read 10141 times)

0 Members and 1 Guest are viewing this topic.

princess prin prin

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 238
  • Last login:Today at 04:30:52 am
  • intrinsically safe
Re: Hantarex Polo/2 25-28 Dead - how to test B+
« Reply #40 on: January 19, 2020, 03:54:05 pm »
Quote from: perjmolsen on January 19, 2020, 02:05:25 pm
So I am thinking that the C96 is the issue.
Currently I have a 472J cap in.
If I change it to a 4.7uf the picture is to small....

Why did you change the value from 4.7uF which is correct to 0.0047uF (that's what 472 is)??
If you can't adjust width and you have a pincushion distortion it's because the correction signal from T19 is either missing or it doesn't arrive at the diodes. I'm wondering if the bridge/width coil is the problem. Or R135.
« Last Edit: January 19, 2020, 10:39:36 pm by princess prin prin »
Logged

perjmolsen

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 429
  • Last login:December 08, 2022, 04:09:06 am
  • I want to learn, and try.. I NEWER give up :)
    • My gameroom
Re: Hantarex Polo/2 25-28 Dead - how to test B+
« Reply #41 on: January 19, 2020, 04:59:32 pm »
Hi

THANKS!  ;D  :notworthy:

It where R137 that where dead!   :cheers:
Put in a new 10 ohm resistor, and now I am able to adjust picture  :applaud:
Logged

princess prin prin

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 238
  • Last login:Today at 04:30:52 am
  • intrinsically safe
Re: Hantarex Polo/2 25-28 Dead - how to test B+ (SOLVED)
« Reply #42 on: January 19, 2020, 10:42:32 pm »
I don't work much on these later POLOs and I didn't notice there was a resistor in series with the EW signal until I looked at the schematics last night. Earlier Hantarex chassis don't have it.
Logged

perjmolsen

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 429
  • Last login:December 08, 2022, 04:09:06 am
  • I want to learn, and try.. I NEWER give up :)
    • My gameroom
Re: Hantarex Polo/2 25-28 Dead - how to test B+ (SOLVED)
« Reply #43 on: January 20, 2020, 05:30:55 am »
Quote from: princess prin prin on January 19, 2020, 10:42:32 pm
I don't work much on these later POLOs and I didn't notice there was a resistor in series with the EW signal until I looked at the schematics last night. Earlier Hantarex chassis don't have it.

Still I am amazed of you and grantspain  :notworthy:
Logged
Pages: 1 [2]  All
  
Go Up
« previous next »