Software Support > GroovyMAME
GroovyArcade live-CD 2022 (collaborative effort)
Substring:
need network to get what's happening. How familiar are you with linux ? We'll need you to get a software called putty to type some remote commands. The logs I need can be obtained through windows network shares
robbbby:
--- Quote from: Substring on June 20, 2021, 05:11:04 pm ---need network to get what's happening. How familiar are you with linux ? We'll need you to get a software called putty to type some remote commands. The logs I need can be obtained through windows network shares
--- End quote ---
I know how to use putty and ssh/telnet into another machine. As far as linux I only know the very basic of commands to get around the filesystem.
I did however get groovyarcade installed. I disabled the onboard gpu like was recommended and it worked fine.
Now I need to figure out how to do everything else :o
robbbby:
Already ran into issues.
I followed the GA wiki and ran pacman to do a full system upgrade. I think it went fine, but after reboot it doesn't load attract mode, just the main GA menu. When I go into the options, select attract mode as the front end, then try and start the front end, nothing happens.
Not sure if this helps but this is the attract.log
--- Quote ---*** Initializing display: 'MAME'
- Loaded master romlist 'MAME' in 1 ms (60 entries kept, 0 discarded)
- Constructed 2 filters in 0 ms (120 comparisons)
[ALSOFT] (EE) Failed to set real-time priority for thread: Operation not permitted (1)
[ALSOFT] (EE) Failed to set real-time priority for thread: Operation not permitted (1)
Sound file not found: sloop.mp3
Failed to get output info for.primary monitor position
Sound file not found: sstart.mp3
- Loaded layout: /home/arcade/shared/frontends/attract/layouts/Basic/ (layout.nut)
- Working directory: /home/arcade/shared/configs/mame/
*** Running: /opt/galauncher/galauncher.sh groovymame arcade wrally
Switchres: Modeline "368x232_60 15.660000KHz 60.000000Hz" 7.485480 368 383 418 478 232 238 241 261 -hsync -vsync
ALSA lib pcm.c:2660:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear
ALSA lib pcm.c:2660:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe
ALSA lib pcm.c:2660:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side
ALSA lib pcm_route.c:877:(find_matching_chmap) Found no matching channel map
tibpal20l8-25cnt.b23 ROM NEEDS REDUMP
gal16v8-25lnc.h21 NOT FOUND (NO GOOD DUMP KNOWN) (tried in wrally)
tibpal20l8-25cnt.h15 ROM NEEDS REDUMP
WARNING: the machine might not run correctly.
Unable to create history.db
Unable to create history.db
Unable to create history.db
Average speed: 100.02% (48 seconds)
Failed to get output info for.primary monitor position
[ALSOFT] (EE) Failed to set real-time priority for thread: Operation not permitted (1)
Failed to get output info for.primary monitor position
Sound file not found: sloop.mp3
- Loaded layout: /home/arcade/shared/frontends/attract/layouts/Basic/ (layout.nut)
Attract-Mode v2.6.1 (Linux, SFML 2.5.1 +FontConfig +Xinerama +SWF +7z +Curl)
avcodec 58.54.100 / avformat 58.29.100 / swscale 5.5.100 / avutil 56.31.100 / swresample 3.5.100
--- End quote ---
And one other stupid question. I've searched and cannot find anything, and when I was running GM under windows it worked out of the box.... How do I map my joysticks? None of the controllers or buttons work. I have a JPAC PC to Jamma.
Substring:
For the big update that has problems with AM not loading, just run sudo chmod +s /usr/lib/Xorg.wrap (it's a bug on Arch side, they haven't replied yet)
Joysticks do work on Linux GM. That they were mapped automatically is a different thing ;) When you press TAB and go the the input settings, your pads are not responding ?
robbbby:
--- Quote from: Substring on June 22, 2021, 03:29:26 am ---For the big update that has problems with AM not loading, just run sudo chmod +s /usr/lib/Xorg.wrap (it's a bug on Arch side, they haven't replied yet)
Joysticks do work on Linux GM. That they were mapped automatically is a different thing ;) When you press TAB and go the the input settings, your pads are not responding ?
--- End quote ---
Awesome, got it up and running and some Roms imported.
My romset is 0.232, GM is 0.229. Will I have issues or should GM be upgraded.
When I go to input controls in GM my joysticks and buttons still aren’t working. Is there anyway to see if the JPAC is recognized via the USB connection?
Thanks
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version