| Main > Everything Else |
| 3D Printing : Arcade Edition Thread |
| << < (34/63) > >> |
| yotsuya:
Here, I zoomed in on the pic for you. You can see the two pieces. Anyone here do Octoprint? |
| Howard_Casto:
That should work. I haven't really seen the need for Octoprint. It's a really cool idea, but these are Chinese printers so I'm too terrified to leave it unattended for too long. |
| ark_ader:
--- Quote from: yotsuya on February 25, 2019, 07:39:41 am --- --- Quote from: ark_ader on February 25, 2019, 07:00:23 am --- --- Quote from: yotsuya on February 24, 2019, 09:00:34 pm --- Just read this. I知 actually building an enclosure this weekend. Bought 3 IKEA Lacks and am printing the parts as I type. I saw one some friends set up and it痴 perfect. --- End quote --- Lately it has been getting cooler in the garage, and it has been hard to get the bed up to temperature. So that lack enclosure is becoming a necessity. Are you going with glass or lexon? --- End quote --- I知 going to go with plexi, but I致e got a few ideas to give it a bit more flair. I値l post pics as I build. Here痴 where I知 currently at... --- End quote --- That looks awesome. Your prints look very nice indeed. :applaud: I cannot wait until it is finished. Are you going to add a temperature sensor too? I have some lacks going spare (was for lack arcade) and I will do the same. I got one of IKEA's small BEKVﾄM carts to put the printer on and have a spare PC underneath. I also got octoprint working on a Pi zero W, and I know about the streaming issue, but I bought the small camera for time lapse. Have you seen the palette pro yet? https://www.mosaicmfg.com/ :o |
| yotsuya:
--- Quote from: Howard_Casto on February 27, 2019, 12:23:54 am ---That should work. I haven't really seen the need for Octoprint. It's a really cool idea, but these are Chinese printers so I'm too terrified to leave it unattended for too long. --- End quote --- The first thing I did was add a MOSFET, so I知 pretty confident nothing is going to catch fire. One thing I知 going to do when I move the setup over is the remove the power supply from the printer and mount it under the top enclosure. I知 also going to take the LCD off the top of the frame and move it to a more convenient location. |
| yotsuya:
--- Quote from: ark_ader on February 27, 2019, 05:18:01 am --- --- Quote from: yotsuya on February 25, 2019, 07:39:41 am --- --- Quote from: ark_ader on February 25, 2019, 07:00:23 am --- --- Quote from: yotsuya on February 24, 2019, 09:00:34 pm --- Just read this. I知 actually building an enclosure this weekend. Bought 3 IKEA Lacks and am printing the parts as I type. I saw one some friends set up and it痴 perfect. --- End quote --- Lately it has been getting cooler in the garage, and it has been hard to get the bed up to temperature. So that lack enclosure is becoming a necessity. Are you going with glass or lexon? --- End quote --- I知 going to go with plexi, but I致e got a few ideas to give it a bit more flair. I値l post pics as I build. Here痴 where I知 currently at... --- End quote --- That looks awesome. Your prints look very nice indeed. :applaud: I cannot wait until it is finished. Are you going to add a temperature sensor too? I have some lacks going spare (was for lack arcade) and I will do the same. I got one of IKEA's small BEKVﾄM carts to put the printer on and have a spare PC underneath. I also got octoprint working on a Pi zero W, and I know about the streaming issue, but I bought the small camera for time lapse. Have you seen the palette pro yet? https://www.mosaicmfg.com/ :o --- End quote --- I知 probably going to buy a Pi for the project if I do it, so I値l get a regular one, not the Zero. I do want to add a camera. Also thinking about doing this auto level kit. Any experience/recommendations? |
| Navigation |
| Message Index |
| Next page |
| Previous page |