Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Lightguns Arcade1Up Try the site in https mode Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news

  

Author Topic: Groovymame doesn't recognize very brief input from coin mech  (Read 9392 times)

0 Members and 1 Guest are viewing this topic.

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Groovymame doesn't recognize very brief input from coin mech
« on: March 27, 2017, 01:16:02 am »
Wondering if anyone has encountered this. My machine has a coin mech which sends a very brief input through when a coin is dropped. It's working "fine" meaning arcade PCBs recognize the coins with no problem and when I hook up my j-PAC it works as expected if I press down on the coin trigger with my finger and raise it again slowly. If I flip it very fast or drop an actual coin through, the input seems to be too brief for mame (windows?) to notice and it's like no coin was added. Anything I can do?
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

RobeeJ

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 120
  • Last login:Yesterday at 04:36:19 am
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #1 on: March 27, 2017, 03:35:46 am »
I've never had this problem with any of the I-PACs I've used over the years. :(

My coin mech uses a relay to close a circuit, does yours? Or does it use a different mechanism? Also do you have an oscilloscope?

Paradroid

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 687
  • Last login:March 10, 2024, 04:41:43 am
    • SCART Hunter
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #2 on: March 27, 2017, 04:16:38 am »
I have experienced something similar using an early version of Ultimarc's rotary encoder that I bought from eBay: Windows apps (e.g. Noyepad) would recognise the key presses but not MAME! I read that Ultimarc released a revision with longer "key down" times.

In my case, I solved the problem by creating an AutoHotkey that catches the key presses from the encoder and resends to MAME with a longer key press time (maybe 20 ms from memory?) This solved the issue in my case.

Is your J-Pac an early model or something?


Sent from my SM-A300Y using Tapatalk

My MAME/SCART/CRT blog: SCART Hunter

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #3 on: March 27, 2017, 05:45:31 am »
No, not an early model. Bought this year.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

yotsuya

  • Trade Count: (+21)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 19955
  • Last login:March 17, 2024, 12:41:11 am
  • 2014 UCA Winner, 2014, 2015, 2016 ZapCon Winner
    • forum.arcadecontrols.com/index.php/topic,137636.msg1420628.html
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #4 on: March 27, 2017, 09:16:01 am »
Check the switch on the coin mech.
***Build what you dig, bro. Build what you dig.***

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #5 on: March 27, 2017, 10:33:33 am »
Yotsuya, not sure what you mean? The switch works fine, it works with my finger thru the j-pac and adds a credit in mame when I push the wire down. It also works with a PCB either with my finger or a coin dropped through. It doesn't work with the j-pac/mame with a coin drop (it seems to be flipping too fast/brief).
« Last Edit: March 27, 2017, 12:32:38 pm by Tzakiel »
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

krick

  • Trade Count: (+1)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 2006
  • Last login:February 08, 2023, 08:30:27 pm
  • Gotta have blue hair.
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #6 on: March 27, 2017, 11:25:30 pm »
What game(s) are you testing with?  Each game handles their own coin inputs.  Maybe something is wrong with the driver for that game.
Hantarex Polo 15KHz
Sapphire Radeon HD 7750 2GB (GCN)
GroovyMAME 0.197.017h_d3d9ex
CRT Emudriver & CRT Tools 2.0 beta 13 (Crimson 16.2.1 for GCN cards)
Windows 7 Home Premium 64-bit
Intel Core i7-4790K @ 4.8GHz
ASUS Z87M-PLUS Motherboard

yotsuya

  • Trade Count: (+21)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 19955
  • Last login:March 17, 2024, 12:41:11 am
  • 2014 UCA Winner, 2014, 2015, 2016 ZapCon Winner
    • forum.arcadecontrols.com/index.php/topic,137636.msg1420628.html
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #7 on: March 27, 2017, 11:41:00 pm »
Some real games like Ms. Pac-Man has issues with coins falling too fast to trigger a pulse. See what krick said 
***Build what you dig, bro. Build what you dig.***

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #8 on: March 28, 2017, 08:38:12 am »
Oh that's interesting! I was testing with Ketsui so maybe I'll try another.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #9 on: March 29, 2017, 07:34:53 am »
Test results:

Windows notepad: coin drop works every time (it types "5")
About 2/3 of games tested: coin drop works fine
About 1/3 of games tested: coin drop doesn't work, slightly longer press of coin trigger does work.

It's a large number of games that don't seem to like the brief coin switch input. What can I do? Is this a MAME issue, driver issue with all those games, or just my coin switch has an unusually brief action? When I use the coin shortcut with p1 start and p1 button 1, it also needs a slightly longer press to work on many games. Longer than just a quick tap.

There are two things I can think of/ have been suggested:

1. Use autohotkey to "catch" when "5" is entered and send a longer input (as suggested above by Paradroid)

2. Andy suggested I attach a 10uf capacitor to the switch + and - terminals which should enlongate the pulse.

I like the autohotkey idea, but my concern is that if I install the PCBs of the games that have the issue in MAME, the coin input may not work. What do you think?
« Last Edit: March 29, 2017, 07:42:30 am by Tzakiel »
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #10 on: March 29, 2017, 07:11:29 pm »
Typically coin mechs (electronic) have a coin pulse selector 25ms/50ms/75ms/100ms or similar.

This is to ensure the pulse is actually a true signal.
Likewise if you HOLD the coin button for a long period - Many games will report a "Coin Error" - Thinking the switch is shorted.

Obviously some games expect slightly different coin pulse periods - But generally you are safe between 50ms~100ms.

In the past, Most mechanical coin mechs would be connected to a credit pcb which would catch the trigger and output a signal pulse.

So your true solution would be to get a Credit PCB or preferably create a small circuit that holds the signal for a small time (50ms-100ms).
It's also worth ensuring the circuit acts as a debounce as many people report issues of multiple credits on a coin trigger.
 
« Last Edit: March 29, 2017, 07:24:59 pm by ozfalcon »

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #11 on: March 29, 2017, 07:22:27 pm »
2. Andy suggested I attach a 10uf capacitor to the switch + and - terminals which should enlongate the pulse.

I like the autohotkey idea, but my concern is that if I install the PCBs of the games that have the issue in MAME, the coin input may not work. What do you think?
I'd recommend trying what Andy suggested first. It's the more robust and simple solution.

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #12 on: March 29, 2017, 08:21:44 pm »
I think I'll try adding a cap to the switch. Any idea how this is done? I buy a cap and I guess I need to solder it on? Any tips? I've never soldered.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #13 on: March 29, 2017, 08:23:41 pm »
Ozfalcon, any idea if my coin mech could be set to a longer pulse? It's a blast city mech, it just looks like a little black box with a wire coming out.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #14 on: March 30, 2017, 12:06:40 am »
Ozfalcon, any idea if my coin mech could be set to a longer pulse? It's a blast city mech, it just looks like a little black box with a wire coming out.

In your first post, You mention pressing on the coin trigger.  Is that "Trigger" a micro switch?


Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #15 on: March 30, 2017, 12:34:52 am »
It's a little black box with a wire sticking out attached to a rotary thing. Press down on the wire (as a coin would when dropped thru) activates a clicking switch inside the housing.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #16 on: March 30, 2017, 05:33:14 am »
It's a little black box with a wire sticking out attached to a rotary thing. Press down on the wire (as a coin would when dropped thru) activates a clicking switch inside the housing.

Do a Google search for coin mech microswitch and see if it looks similar. There should be two terminals used on the switch.

RobeeJ

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 120
  • Last login:Yesterday at 04:36:19 am
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #17 on: March 30, 2017, 05:34:36 am »
I think I'll try adding a cap to the switch. Any idea how this is done? I buy a cap and I guess I need to solder it on? Any tips? I've never soldered.

Yes you need to solder it on, it will be polarised so the negative terminal needs to go to ground. This should probably be done on the J-Pac board.

You may want to just explore adjusting the pulse selector on the coin mech itself first if it has one, look up any dip switches.

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #18 on: March 30, 2017, 08:33:13 am »
This is the switch. Nothing on it to adjust that I can see.

The cap should just be attached to the metal spades that the wiring plugs into right? Near the top so the plugs can still slide on. So it will just stick out.

My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #19 on: March 30, 2017, 06:14:25 pm »
This is the switch. Nothing on it to adjust that I can see.

The cap should just be attached to the metal spades that the wiring plugs into right? Near the top so the plugs can still slide on. So it will just stick out.

That's a standard coin mech switch - And it should work ok.

You have three simple options to try first.
1. The switch might be worn out or faulty. They are cheap - But one online at ebay or an online Arcade supplier.
2. See the slight angle in the wire, You could bend it some more to give the rotation more action when a coin drops.
3. Try the capacitor between the spade connectors as a last resort (From option 1 & 2).

If this coin mech is second hand (Not new) then it is more likely 1 or 2.

<Added>
Also, Check the emulation speed of the games that cause this. If your PC is not up to speed - Then the game might see the coin input as a shorter pulse that it actually is.
 
« Last Edit: March 30, 2017, 06:49:34 pm by ozfalcon »

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #20 on: April 01, 2017, 08:01:16 pm »
Update: I tried the cap on the switch and it didn't seem to do anything at all. I also tried another coin microswitch and got same result. It seems a wide variety of games just don't take coin inputs easily. Maybe it's a general MAME problem. Too bad.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #21 on: April 02, 2017, 05:32:55 am »
Update: I tried the cap on the switch and it didn't seem to do anything at all. I also tried another coin microswitch and got same result. It seems a wide variety of games just don't take coin inputs easily. Maybe it's a general MAME problem. Too bad.

No it's not a general Mame problem.

What games specifically is this problem happening?
« Last Edit: April 02, 2017, 05:49:38 am by ozfalcon »

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #22 on: April 02, 2017, 05:48:38 am »
Update: I tried the cap on the switch and it didn't seem to do anything at all. I also tried another coin microswitch and got same result. It seems a wide variety of games just don't take coin inputs easily. Maybe it's a general MAME problem. Too bad.

I played a game of Ketsui (ket)

Looks like what @krick and @yotsuya have mentioned is more than likely the case.
ie. Some real games like Ms. Pac-Man has issues with coins falling too fast to trigger a pulse.

The game seems to run fast enough on moderate hardware (Benchmarks @400% on my old machine here).
The coin trigger is consistent in it's operation - So it's not emulation slowdowns.

The easiest solution would be to buy a cheap electronic coin mech from ebay ($20).
You can then set the coin drop pulse to 100ms - Which should be enough to trigger games like this.

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #23 on: April 02, 2017, 08:53:37 am »
Thanks ozfalcon. I'll check that out. I just look up electronic coin mech? Will that also work with real pcbs?
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #24 on: April 02, 2017, 08:57:50 am »
I guess I should be more specific. I want to keep my coin validation and drop etc because they take 100yen coins and are part of my Blast City cabinet. It's just the microswitch part I would like to replace or change to a longer pulse. Is there something I could just replace the little switch with that is programmable?
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #25 on: April 02, 2017, 06:32:57 pm »
I guess I should be more specific. I want to keep my coin validation and drop etc because they take 100yen coins and are part of my Blast City cabinet. It's just the microswitch part I would like to replace or change to a longer pulse. Is there something I could just replace the little switch with that is programmable?

No.
But you CAN install a Credit PCB - Which should condition the signal to be more acceptable.

Otherwise - Just pull the existing coin mech out (Store it - Don't throw it out) - And install the electronic coin mech.
If you get a 5 coin type acceptor - You can program each coin type to signal a credit.
eg. 20c, 100yen, Quarter etc.

Do an ebay search for "5 coin acceptor"


ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #26 on: April 02, 2017, 06:33:30 pm »
Thanks ozfalcon. I'll check that out. I just look up electronic coin mech? Will that also work with real pcbs?

Yes it will work with real PCB's

Trnzaddict

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 175
  • Last login:September 24, 2023, 12:12:29 pm
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #27 on: April 03, 2017, 09:20:40 am »
Just wanted to chime in because I ran into this problem with my coin door as well on my machine with MAME, Specifically with the Cave games. One of the later DoDonpachi games and mmpork is very finicky with coin drops.
With mmpork if it's not right it'll spill out a coin mech error and the game will need to be reset.

Iirc, I think I made individual ini files for problem games and screwed with the coin impulse options for those?

Another option is use a directinput enabled version of mame for these games and write an autohotkey script that  runs that would keep your coin button held down a little longer. For example if your coin door is mapped to 5 in your encoder you could do:

5::
Send, {5 down}
sleep, 100
Send, {5 up}

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #28 on: April 03, 2017, 09:43:21 am »
 Oh wow, that's great information.  I had no idea that the ini files could help with that.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #29 on: April 03, 2017, 04:03:25 pm »
Setting coin_impulse to 10000 fixed it. Hah! I'm still confused a bit though, does this mean people who own espgaluda and ketsui pcbs can't get credits working with a normal Japanese coin mech? Or are the mame drivers incorrect for those two games?
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #30 on: April 03, 2017, 07:03:05 pm »
Oh wow, that's great information.  I had no idea that the ini files could help with that.

Me neither, Learn something new every day!

Will have to learn more about this - What it's value represents etc.

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #31 on: April 03, 2017, 11:20:13 pm »
Setting coin_impulse to 10000 fixed it. Hah! I'm still confused a bit though, does this mean people who own espgaluda and ketsui pcbs can't get credits working with a normal Japanese coin mech? Or are the mame drivers incorrect for those two games?

After some investigation, I now understand how it works - And the value of 10000 is WRONG.

coin_impulse is calculated by the number of frames per second the game runs at (Refresh rate)
The game Ketsui (ket) runs at refresh="59.170000" (Lets just say 60fps to make it easy).

So for a 1 second coin pulse, The value of 60 should be used.
1 second   coin_impulse 60
2 seconds  coin_impulse 120
4 seconds  coin_impulse 240

WARNING - The coin impulse is a "BYTE" meaning it has a range of 0-255.
Any values over this may be either cycling 256 or unpredictable.
(Example the value of 256 gives NO coin_impulse and increments up the same as starting from 0)




« Last Edit: April 03, 2017, 11:24:42 pm by ozfalcon »

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #32 on: April 04, 2017, 05:19:13 am »
How did you figure it out? I searched a lot for info on it and found none. I also tried 1, 2, 100, 1000, before landing on 10000 which worked for all games except muchi muchi pork so I made a separate ini for that game with impulse set back to zero.

I'll try 60 I guess and see how it goes.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #33 on: April 04, 2017, 06:22:09 pm »
How did you figure it out? I searched a lot for info on it and found none. I also tried 1, 2, 100, 1000, before landing on 10000 which worked for all games except muchi muchi pork so I made a separate ini for that game with impulse set back to zero.

I'll try 60 I guess and see how it goes.

The first thing I noticed was altering 10000 did not change the impulse time as expected.
ie. 20000 didn't make it twice as long.

Next I looked up the docs ;) http://docs.mamedev.org/commandline/commandline-all.html but it was unclear what "n" actually was.
After some deliberation (irc) it was considered to be either Frames or CPU cycles - Preference toward frames.

Then I loaded a game (1944), Entered Service mode (F2) then selected Input test and observed the coin trigger duration.
Exit the game, Alter the coin_impulse then checked it again.
After a little trial and error, I figured it was cycling 0-255 (Hence 1 byte).

« Last Edit: April 04, 2017, 06:26:33 pm by ozfalcon »

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #34 on: April 04, 2017, 06:25:45 pm »
40 works fine for me so I suspect you are right. I just figured that when 100 and 1000 didn't work I needed to go higher.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #35 on: April 04, 2017, 06:31:43 pm »
40 works fine for me so I suspect you are right. I just figured that when 100 and 1000 didn't work I needed to go higher.

I'm not sure why 100 didn't work (Too long!?).
I will have to give that value a try with Ketsui (ket).

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #36 on: April 04, 2017, 07:15:52 pm »
40 works fine for me so I suspect you are right. I just figured that when 100 and 1000 didn't work I needed to go higher.

 I gave Ketsui (ket) a check and found the upper and lower values it can accept (Probably a slight variance between machines).
# coin_impulse 77 Fails.
coin_impulse 7~8 Should be a safe value (~120 to ~135 milliseconds).
# coin_impulse 5 Fails.

The lower the value, the faster coins can be accepted.
eg. Value of 40 is just over half a second per coin drop.
(ie. 60 frames per second, 30 being half)
« Last Edit: April 04, 2017, 07:48:29 pm by ozfalcon »

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #37 on: April 04, 2017, 07:29:37 pm »
40 works fine for me so I suspect you are right. I just figured that when 100 and 1000 didn't work I needed to go higher.

If we do some simple math we can work out the pulse in milliseconds.

1 (second) ÷ 59.170000 (refresh) = 0.016900456 (seconds per frame)

0.016900456 x 6 = 0.10140274 (seconds)

0.10140274 x 1000 = 101.40274 (milliseconds)

So ket needs a minimum of aprox 100 milliseconds to trigger a credit.
Which is not that common really - But at least we know what it's doing.

<Updated previous post to 7~8 safe value>
« Last Edit: April 04, 2017, 07:48:05 pm by ozfalcon »

Tzakiel

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 272
  • Last login:March 02, 2019, 12:59:01 pm
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #38 on: April 04, 2017, 08:03:55 pm »
It's probably PGM polygame master board games. Espgaluda and knights of valor are other examples.

I still don't get why this is a thing. I know espgaluda and ketsui both ran in Japanese arcades with the same coin drop and cab that I have. Maybe it's a mistake with the mame driver for PGM.

Anyway glad to have a fix.
My Fighter CRT Cabinet Thread: Tzakiel's 2P Cabinet

ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #39 on: April 04, 2017, 10:58:59 pm »
It's probably PGM polygame master board games. Espgaluda and knights of valor are other examples.

I still don't get why this is a thing. I know espgaluda and ketsui both ran in Japanese arcades with the same coin drop and cab that I have. Maybe it's a mistake with the mame driver for PGM.

Anyway glad to have a fix.

Perhaps (probably) the coin mech 1st went to a Credit PCB (Very common), Which then signaled the Main game board with a specific coin pulse (~100ms+).

It could be mistake in the driver (I'm not skilled enough to confirm or deny the driver integrity).
However - It appears to me that it's the actual game code that is determining what is too short or too long a pulse.

Either way - Something new learned is good and something to keep in mind when other coin issues arise.



ozfalcon

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 156
  • Last login:April 07, 2022, 04:55:03 am
  • ZSystem
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #40 on: April 04, 2017, 11:04:36 pm »
It's probably PGM polygame master board games. Espgaluda and knights of valor are other examples.

I still don't get why this is a thing. I know espgaluda and ketsui both ran in Japanese arcades with the same coin drop and cab that I have. Maybe it's a mistake with the mame driver for PGM.

Anyway glad to have a fix.

There does appear to be a bug in the coin_impulse code, In that the doc say if value is smaller than 0 then disable the impulse.
(n<0 disable impulse, n==0 obey driver, 0<n set time n).

However when setting the value to -1 or smaller, The coin_impulse still fires (As if the value was 0 == obey driver which usually means for as long as the key is held down).

<Added>
On second thought,
It may be that some drivers force a "coin_impulse n" - And the disabling option might be for those specific cases.
But generally (most drivers?) would simply make the pulse the length of the key press when obeying the driver.
« Last Edit: April 04, 2017, 11:16:58 pm by ozfalcon »

Rupert H

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 14
  • Last login:October 14, 2023, 03:53:15 am
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #41 on: February 18, 2020, 04:19:57 am »
I see you all solved this problem three years ago, but I think I may be misunderstanding the solution. I have a Groovy MAME cab and it’s not recognising coin insertions for the three CAVE PGM titles (ESPGaluda, Ketsui and DDP DOJ). I’ve seen that I can fix this by changing the coin_impulse setting, so I created a pgm.ini file with coin_impulse set to 8 and dropped it into the MAME/ini folder, as per Ozfalcon’s advice. Unfortunately it’s still not reading coin drops, leading me to believe I’ve formatted the ini file wrongly.

I’ve tried the following:

“coin_impulse 8         1”

and

“coin_impulse            8”

Can anybody tell me exactly how to format this ini file? 🙏



Rupert H

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 14
  • Last login:October 14, 2023, 03:53:15 am
  • I want to build my own arcade controls!
Re: Groovymame doesn't recognize very brief input from coin mech
« Reply #42 on: June 14, 2020, 09:30:41 am »
Anybody got any idea how to help with the above? I’d massively appreciate it.