Main Restorations Software Audio/Jukebox/MP3 Everything Else Buy/Sell/Trade
Project Announcements Monitor/Video GroovyMAME Merit/JVL Touchscreen Meet Up Retail Vendors
Driving & Racing Woodworking Software Support Forums Consoles Project Arcade Reviews
Automated Projects Artwork Frontend Support Forums Pinball Forum Discussion Old Boards
Raspberry Pi & Dev Board controls.dat Linux Miscellaneous Arcade Wiki Discussion Old Archives
Site News

Unread posts | New Replies | Recent posts | Rules | Chatroom | Wiki | File Repository | RSS | Submit news


  

Author Topic: Ami r84 voltage problem  (Read 126 times)

0 Members and 1 Guest are viewing this topic.

Phill sugden

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 3
  • I want to build my own arcade controls!
Ami r84 voltage problem
« on: March 07, 2017, 10:39:56 am »
Hi
I have a ami r84 jukebox i am trying to find the correct voltage for the power supply unit
I have on mine 28vdc 28vac and 11.5 to 14. Should the 11.5 to 14 be 8vdc as on the psu
Or is this accepotable
Phill

ami-man

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 878
Re: Ami r84 voltage problem
« Reply #1 on: March 14, 2017, 06:22:46 am »
Hi Phil,

On the 8 Volts DC it is normally about 7.9 volts with a sall load of a test lamp on it.
If the voltage is 11.5 to 14 volts, had better get the power supply unit checked out and the CCC as well because it may have damaged components in the CCC.

Regards
Alan

Alan Hood
ami-man
UK

Phill sugden

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 3
  • I want to build my own arcade controls!
Re: Ami r84 voltage problem
« Reply #2 on: March 17, 2017, 12:03:26 pm »
Hi alan
Thanks for the phone chat
I have the board out it's a ami 6-08873-01 power supply board
The capacitors c502 c503 c504
Axial capacitors c501 1500uf 50 v c500 3300uf 35 v all bulging on the ends
Will change them
What value are the zener diodes cr501 & cr505
Resistors r510 & r501 I cannot see the banding colours there discoloured
Do you have the values and wattage
Are the capacitors anything special or just standard ones
Schematics diagram would be asking too much
Thanks again regards
Phill

ami-man

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 878
Re: Ami r84 voltage problem
« Reply #3 on: March 20, 2017, 06:18:21 am »
Hi Phil,

C501 should be 1250 mfd 50 volt
CR515 is 13 volts
CR501 is 7.5 volts
R501 is 470 ohms 1/4 watt
R510 is 0.82 ohms 2 watt (wire wound)

Regards
Alan

Alan Hood
ami-man
UK
« Last Edit: Yesterday at 09:22:15 am by ami-man »

Phill sugden

  • Trade Count: (0)
  • Jr. Member
  • **
  • Offline Offline
  • Posts: 3
  • I want to build my own arcade controls!
Re: Ami r84 voltage problem
« Reply #4 on: March 22, 2017, 02:47:20 pm »
Hi alan
Thanks for the info but the resistor I can't see is r510 not r512
Iam going to change the transistors q500 q501 & q502 is the mpsa06 an equivalent
Are the cr500 & cr506 Zener diodes & what value
The c501 1500uf looks original but I will change it
Thanks again
Phill

ami-man

  • Trade Count: (0)
  • Full Member
  • ***
  • Offline Offline
  • Posts: 878
Re: Ami r84 voltage problem
« Reply #5 on: Yesterday at 09:27:17 am »
Hi Phil,

I have edited the above message regardin R510

CR500 & CR506 to CR514 are just silicon diodes.
Q500 to Q502 are NPN transistors

Regards
Alan

  
 

Sitemap 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31