Main > Main Forum

Anymore news on the KADE?

Pages: << < (2/3) > >>

MTPPC:

I bought a batch of 6 MinimusAVRs to start with. I bought these terminal blocks which worked fine: http://www.ebay.com/itm/10pcs-12-Poles-2-54mm-0-1-PCB-Universal-Screw-Terminal-Block-/400263584173?ssPageName=ADME:L:OC:US:3160

The problem I am having is the consistency of the Minimus AVR. My first one went bad and lost its mind after about 8 hours of use. When I tried to reprogram it, it wouldn't take the programming.

My second one is working for several hours at a time, but it, too, is forgetting its programming. I installed the FLIP software on my virtual pinball so I can reprogram it. When I first program the chip, it fails the verification. If I try a second time, it works. It seems to fail over long periods of non-use, but running. I will replace it with a third one, but if the KADE is burdened with this kind of failure rate, it will be a long uphill battle. I'm thinking my machine might have a bad ground or some other problem, but I don't know. The one I gave away has worked flawlessly for well over 60-80 hours.

PL1:

MTPPC: Sorry to hear about your unfortunate run of luck with the AVRs.

Everything I've seen points toward AVRs being pretty rugged. 

Sharpfork posted on another board:

--- Quote ---I had the thing completely wired wrong to the point where it got hot enough to discoloer the little piece of masking tape I put on it and it still works fine. Hell, Rodney even boiled one of the AVRs in water based black dye and it still works. These little buggers are tough!

--- End quote ---

I'd check both your ground and your wire routing/distances.  If you have relays, solenoids, shaker motors or AC wiring too close to unshielded wires, the expanding and collapsing magnetic fields can induce a voltage spike.

Your problem may be similar to what Supafraud was posting here about his mini-pac resetting when he would press flipper buttons.


--- Quote from: jimmer on January 14, 2013, 09:37:03 pm ---I haven't even ordered my MinimusAVR yet, but will be thinking about trying to program it using the info linked above, if the new software isn't released by the time I've built my panel.

--- End quote ---

Degenatrons has some AVR Encoders already programmed (firmware upgrades effortlessly to KADE), labeled and soldered.  If you don't have the AVR and terminals yet, and plan on only doing 1 or 2 AVRs, it will probably be less expensive to order from him. (PM him for details.)



Scott

jimmer:


--- Quote from: PL1 on January 15, 2013, 02:06:30 am ---Degenatrons has some AVR Encoders already programmed (firmware upgrades effortlessly to KADE), labeled and soldered.  If you don't have the AVR and terminals yet, and plan on only doing 1 or 2 AVRs, it will probably be less expensive to order from him. (PM him for details.)

--- End quote ---

Thanks, I will try that.

I did email him a day or so ago asking when KADEs will be available for people who missed the kiskstarter, no reply yet but I guess his inbox is full of KADE questions and he must be full on at the moment.



degenatrons:


--- Quote from: jimmer on January 15, 2013, 07:27:05 am ---
--- Quote from: PL1 on January 15, 2013, 02:06:30 am ---Degenatrons has some AVR Encoders already programmed (firmware upgrades effortlessly to KADE), labeled and soldered.  If you don't have the AVR and terminals yet, and plan on only doing 1 or 2 AVRs, it will probably be less expensive to order from him. (PM him for details.)

--- End quote ---

Thanks, I will try that.

I did email him a day or so ago asking when KADEs will be available for people who missed the kiskstarter, no reply yet but I guess his inbox is full of KADE questions and he must be full on at the moment.

--- End quote ---

Jimmer - Thanks for your PM and we discussed getting one of the AVR's sent out to you with terminals.  I'll make it up tomorrow and will be posted out on Monday.

We have just sent an update to our KickStarter backers about the production of rewards.  Here's a link to that update - http://www.kickstarter.com/projects/kadevice/kade-connects-arcade-controls-to-computers-and-con/posts

We will be selling KADE after the KickStarter rewards are mailed out in February.

equlizer:

so what is this other board we would need to use on the 360/wii?  I already have a pee-wii.  can you wire those 2 together?

Pages: << < (2/3) > >>

Go to full version