Main > Retail vendors
-VENDOR- GroovyGameGear.com - Latest updates to our catalog
MotorHedJr:
--- Quote from: RandyT on June 19, 2013, 10:51:29 am ---
--- Quote from: MotorHedJr on June 19, 2013, 10:25:50 am ---Does the GP-Wiz49 require a driver for Linux?
(in my case Ubuntu 8.04 - that's what I'm using w/ AdvMAME/MENU).
Or will it show up as a HID device? Thanks! :)
--- End quote ---
It is an HID device. However, there are a couple of things you might run into. There is no Linux utility to change the modes. I can supply the interface protocol to someone who has some USB experience and would like to write a utility. However, there is also a mode of operation built into the hardware which allows an extra button (JoyMode...also acting as a "shift" button) to do mode switching without software control.
The other thing is the way the joystick axes are reported. It uses the unsigned 8-bit co-ordinate scheme (0-255), which works perfectly under Windows, but for some reason, some Linux builds seem to have ignored this. I have seen folks reporting success by using the Linux joystick calibration utility with builds where it's not supported, but it won't be "plug and play" on those installations like it is in Windows.
--- End quote ---
Randy,
Thanks for the fast response. It sounds like it should be seen by the event node. I'm guessing to run the 'advj' utility to get the kernel name of the device, then just write another 'local rule' (like I did for the mice) - and s/b set to go:
3.2.1 event - Kernel Input-Event interface (Linux)
This driver works in Linux and it uses the new style input-event interface of the Linux kernel.
It supports more than one joystick or light-gun at the same time.
For USB devices this driver doesn't require any configuration. It's able to autodetect all the present hardware.
This driver is also able to correctly report the type of devices found. You should for example expects to have the gas pedal mapped on the gas control of the game.
One last question:
Do you need to calibrate whatever joysticks you're using w/ the GP-Wiz49 everytime you boot up the PC? ??? Thanks! :)
RandyT:
--- Quote from: MotorHedJr on June 20, 2013, 03:28:57 pm ---Thanks for the fast response. It sounds like it should be seen by the event node. I'm guessing to run the 'advj' utility to get the kernel name of the device, then just write another 'local rule' (like I did for the mice) - and s/b set to go:
3.2.1 event - Kernel Input-Event interface (Linux)
This driver works in Linux and it uses the new style input-event interface of the Linux kernel.
It supports more than one joystick or light-gun at the same time.
For USB devices this driver doesn't require any configuration. It's able to autodetect all the present hardware.
This driver is also able to correctly report the type of devices found. You should for example expects to have the gas pedal mapped on the gas control of the game.
One last question:
Do you need to calibrate whatever joysticks you're using w/ the GP-Wiz49 everytime you boot up the PC? ??? Thanks! :)
--- End quote ---
I'll take your word for it. Linux is a bit outside of my current focal range, so at the moment, I have to defer to those with more experience with it. :)
With Windows, where the unsigned 8-bit reports are properly interpreted, no calibration is ever necessary. I can't say for sure with Linux. I would suspect, however, that the calibration utility (if a working one exists) would remember the devices and calibration data, and simply use the calibration data for the device when it is found. If this is the case, it should need to be done only once.
--- Quote from: ramos8414 on June 20, 2013, 01:13:05 am ---The Shipping estimate on your website isn't working .
--- End quote ---
Unfortunately, it's still not. Apparently the USPS is experiencing a very serious problem with their servers. After a long chat with our webhost, and finding nothing wrong on their end, I had a talk with the local postmaster. He is pulling his hair out just trying to file his reports. If I were to guess, it sounds like they may have been hacked in a big way, as robust data systems like the ones they surely use, don't have issues of this magnitude for as long as it seems to be going on.
In the meantime, domestic customers can still select the "Flat Rate Priority" option. If regular Priority mail ends up as less costly, we will change it before the order is charged. International customers will unfortunately need to be patient while this gets worked out. Hopefully, it won't be much longer.
RandyT
RandyT:
It figures that 15 minutes after I update the status, USPS comes back online :banghead:
In any case, everything is working again. Fingers crossed that it stays that way.
RandyT
RandyT:
--- Quote from: happyfunball on June 16, 2013, 11:43:46 am ---I picked up 4 midway 49 way sticks off ebay not too long ago. one of the centering grommets is pretty much shot, and they all have bat handles which I hate.
I noticed you have a replacement grommet, and you used to sell replacement ball top sticks. I assume the grommet will work, but also that you no longer have the ball tops in stock?
--- End quote ---
Sorry I missed this one. I recently found a small cache of the upgraded stainless shafts and special actuators we had made in the past. They are for the original Midway 49-way sticks (.25" grommets), and won't work with the current HAPP version. They are the parts we used on the high end 49-ways we were building. The cost of these is $22.95 each, and includes choice of Hand-Candy Balltops.
Other news.....
About a page back in this thread I mentioned the possibility of offering a custom CNC panel service. Tron84, being an adventurous soul, convinced me to forge ahead by ordering one :).
Here's the nice dedicated trackball panel design he came up with, and which I just finished for him (shown with permission..Thanks Jeff!);
So we'll kick off the GroovyCNC service now on a trial basis and see how it goes. As indicated earlier, $34.95 plus shipping for a custom panel, made from your finished drawings.
Requirements:
* Must be 12" high x 26" long or smaller. 3/4" MDF only, unfinished.
* Files must be supplied in .CDR (Corel versions up to and including X4), .EPS, .AI or .DXF format, in that order of preference. Vector data only.
* If pockets (cuts which aren't all of the way through) are desired, these must be indicated on the files in some manner to show the depth. Pockets may be on one side only.
* No cuts smaller than 1/4" in any dimension.
* Accuracy is very good, typically within about 15 thousandths of an inch. But don't make tolerances too tight. It 's always best to design things with a small amount of leeway to ensure proper fit.
* No complaining. :) If you send a screwed up drawing and you get a part that matches, that's the way it's supposed to work. But I will review designs for obvious issues and will report it if I find one.
* Precision T-Molding slot may be added for an additional $5.00
Let me know if there are any questions, or drop me an email with your design if you wish to order one.
Thanks,
RandyT
tron84:
[/quote]
Other news.....
About a page back in this thread I mentioned the possibility of offering a custom CNC panel service. Tron84, being an adventurous soul, convinced me to forge ahead by ordering one :).
Here's the nice dedicated trackball panel design he came up with, and which I just finished for him (shown with permission..Thanks Jeff!);
So we'll kick off the GroovyCNC service now on a trial basis and see how it goes. As indicated earlier, $34.95 plus shipping for a custom panel, made from your finished drawings.
Requirements:
* Must be 12" high x 26" long or smaller. 3/4" MDF only, unfinished.
* Files must be supplied in .CDR (Corel versions up to and including X4), .EPS, .AI or .DXF format, in that order of preference. Vector data only.
* If pockets (cuts which aren't all of the way through) are desired, these must be indicated on the files in some manner to show the depth. Pockets may be on one side only.
* No cuts smaller than 1/4" in any dimension.
* Accuracy is very good, typically within about 15 thousandths of an inch. But don't make tolerances too tight. It 's always best to design things with a small amount of leeway to ensure proper fit.
* No complaining. :) If you send a screwed up drawing and you get a part that matches, that's the way it's supposed to work. But I will review designs for obvious issues and will report it if I find one.
* Precision T-Molding slot may be added for an additional $5.00
Let me know if there are any questions, or drop me an email with your design if you wish to order one.
Thanks,
RandyT
[/quote]
Thank you Again Randy :cheers: :applaud: :applaud:
It looks Great!!!!! Once again another Great service from GroovyGameGear :cheers: :applaud:
Jeff
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version