Main > Main Forum
No yoke from Ram Controls
<< < (44/51) > >>
Hoopz:

--- Quote from: Bender on January 26, 2011, 09:59:56 am ---
--- Quote from: Cananas on January 23, 2011, 05:35:59 am ---
--- Quote from: Cananas on January 22, 2011, 03:15:42 pm ---I have send an e-mail to Adam, now. Let's wait what happens (Crossed fingers).

--- End quote ---

Adam gave me a fast answer:

--- Quote ---Carlos,

After a quick look, I was able to locate your pending orders for the yoke and usb board.  I will ship them to you on Monday.  If there is anything else, I can certainly help.  I hope that these actions will be to your satisfaction.

Adam


--- End quote ---

Let's hope that finally the yoke will arrive...

--- End quote ---

Cananas,

get the yolk yet?

--- End quote ---
I'd put money on Dave sending him yolks instead of a yoke. 
Cananas:

--- Quote from: Bender on January 26, 2011, 09:59:56 am ---
--- Quote from: Cananas on January 23, 2011, 05:35:59 am ---
--- Quote from: Cananas on January 22, 2011, 03:15:42 pm ---I have send an e-mail to Adam, now. Let's wait what happens (Crossed fingers).

--- End quote ---

Adam gave me a fast answer:

--- Quote ---Carlos,

After a quick look, I was able to locate your pending orders for the yoke and usb board.  I will ship them to you on Monday.  If there is anything else, I can certainly help.  I hope that these actions will be to your satisfaction.

Adam


--- End quote ---

Let's hope that finally the yoke will arrive...

--- End quote ---

Cananas,

get the yolk yet?

--- End quote ---

Yeeeah!!. It is coming here.

Adam provided me the tracknumber yesterday (26 january). I have called UPS today and it will arrive to Spain tomorrow. So the next week will be, finally, at home, I presume.
Bender:

--- Quote from: Hoopz on January 26, 2011, 10:02:36 am ---
--- Quote from: Bender on January 26, 2011, 09:59:56 am ---
--- Quote from: Cananas on January 23, 2011, 05:35:59 am ---
--- Quote from: Cananas on January 22, 2011, 03:15:42 pm ---I have send an e-mail to Adam, now. Let's wait what happens (Crossed fingers).

--- End quote ---

Adam gave me a fast answer:

--- Quote ---Carlos,

After a quick look, I was able to locate your pending orders for the yoke and usb board.  I will ship them to you on Monday.  If there is anything else, I can certainly help.  I hope that these actions will be to your satisfaction.

Adam


--- End quote ---

Let's hope that finally the yoke will arrive...

--- End quote ---

Cananas,

get the yolk yet?

--- End quote ---
I'd put money on Dave sending him yolks instead of a yoke. 

--- End quote ---


Star Wars Yolks! eww!!!
Cananas:
Finally it have arrived today.

The yoke works OK, but... the usb inteface not.

It does not detect the x/y movement. I tried to calibrate but no, no. The potenciometers are OK (from 0 to 2,5K -both axis in parallel, I think ->Xblack are connected with Cblack and Xbrown with Cbrown-) and the wires are also OK, even the header cable that comes with the usb interface to connect the yoke.

So I supposed the problem was on the USB interface. I tried with another potenciometer (5K ohm) (ony this was connected to the PCB). I connected to the usb interface, and the axis x and y (??) move when the potenciometer it was between 0 and 4.95k ohm.

I don't know what happens with the USB interface.
MameMaster!:
I'm pretty sure you have to adjust your usb settings via the JOYSTICK settings on your pc- not via mame.

I made the same mistake and thought that it was broken.

Give that a shot-- try calibrating it via your pc.

Good luck!  :cheers:
Navigation
Message Index
Next page
Previous page

Go to full version